traxxas slash 2wd axle carrier 3d models

These short arms I designed specifically to accommodate a Lightning McQueen body on a Traxxas Nitro Rustler chassis are quite impressive. ...Stock Bandit rear arms were used in their construction.

I wanted to mount my old Slash body on the wall so I made this I have not printed this yet so it might not work

Battery Tie Down with a solid center section to allow the mounting of ESC and Receiver as far back on the slash chassis but keeping the weight centered.

30mm fan mount for slash 4x4 slipper clutch. ... Goes on the right side of the vehicle mounts on upper right engine mount.

Designed a pressfit-carrier to add ~57g weight per wheel for the Tactical-Unit Wheels. I like the Wheels alot because of the scale heavy duty look with central tire Inflation system. ...But i ordered them pre mounted, so i needed a solution to add some...

This is replacement for oryginal Traxxas part number 6893. I recommend to use it as a temoprary solution, it is always better to have a rigid original part. But if you need this part now and you must wait some days for the delivery, this is a working...

These are very short arms I created to fit a Lightning McQueen body onto a Traxxas Nitro Rustler chassis. Stock Bandit rear arms were used. Added V2 model. ...I have not attempted to print it yet, but the dimensions are the same.

Simple print to get a flat surface for the ESC in TRX-7422 LCG chassis. ...Uses same holes in chassis as Traxxas original ESC. ... I made it 3mm thick, cut it in your slicer depending on how thick you want it.

This is replacement for oryginal Traxxas part number 6893. I recommend to use it as a temoprary solution, it is always better to have a rigid original part. But if you need this part now and you must wait some days for the delivery, this is a working...

for PL 1/10 slash raptor body(real scale) miror when you attach on your toy body, each side needs "dia 2mm, length 8mm, 3screws for each side, total 6 screws need)

For my Slash 4x4 ultimate, as a replacement for the original VXL 3S controller The adapter can take controllers up to a maximum width of 40mm Controllers are available here>>> https://amzn.to/33UHdMk Video: https://www.youtube.com/watch?v=74zSqdlPX2Y

A simple plate for mounting esc's to the slash. Uses stock mounting holes and stock screws, the heads are countersunk for a flat mounting surface. Use double-sided tape to stick the esc down, it works extremely well. ... Install video here...

This is a remix of "Akku Träger Slash 4x4 LCG" by Sani007 https://www.thingiverse.com/thing:3740043 The stock battery holders are not flexible enough. With this battery holder I can mount a big 4S pack. I added holes Version 2 : made it more...

I'm doing a slash speed run project without breaking the bank by opting for plastic alternatives instead of metal. They're not only affordable but also incredibly lightweight, making them perfect for printing with ease - the end result is...

I have not attempted to print it yet, but the dimensions are the same. Print instructionsCategory: Toys & Games Summary These are very short arms I created to fit a Lightning McQueen body onto a Traxxas Nitro Rustler chassis. Stock Bandit rear...

I've designed a battery spacer for the Slash 4x4 specifically to address the problems associated with the foam spacers that come with this RC vehicle. These foam spacers often cause wear and tear on the RC over time, making it look aged and worn out....

This is a remix of "Akku Träger Slash 4x4 LCG" by Sani007 https://www.thingiverse.com/thing:3740043 The stock battery holders are not flexible enough. With this battery holder I can mount a big 4S pack. I added holes Version 2 : made it more flush...

These are 0.25mm larger and also 0.1mm closer to the axle shim to reduce slop. I used carbon/nylon filament and printed at 0.1mm layer height. PLA is hard enough and may work fine as long as it doesn't brake. ...I have not done any long term testing...

The bearings are available from traxxas or here cheaper: http://www.kingheads.com/product_info.php?products_id=934 UPDATE 05/05/15: I've updated the design to allow for two motors with a reverse mount on one side. UPDATE 06/16/15: A friend of mine...

This is an updated CC-01 rear axle carrier to be used with custom 4-link suspension. I found the rear stock suspension to be rather lacking on the CC-01, so I made these to be used with various length linkages. ... Good luck!

I remixed Simon's printed axle carriers for the WLToys 124019. I was not rough on the road, yet I had to make out as weak points the three attachment points (see photos attached). Simon's more stable version would not have helped in my case,...

This is a remix of https://www.thingiverse.com/thing:3390838/ I needed a stronger axle carrier and tried a simple modification with tinkercad. Print it not as shown in the thumbnail, flip it upside down and mirror it if you need one for the other...

Rear axle hub carrier for HPI Maverick Strada MT (2017 edition, MV12623), original part number MV22009. Also compatible with: Redcat Volcano EPX Pro, HSP Brontosaurus, Exceed Infinitive, Himoto EMXT-1, Amewi Torche Pro (which are basically the same...

Rear axle hub carrier designed specifically for HPI Maverick Strada MT (2017 edition, MV12623) with original part number MV22009. Also compatible with: Redcat Volcano EPX Pro, HSP Brontosaurus, Exceed Infinitive, Himoto EMXT-1, and Amewi Torche Pro...

Rear axle hub carrier designed specifically for HPI Maverick Strada MT (2017 edition, MV12623), using original part number MV22009. This model is also compatible with other vehicles such as Redcat Volcano EPX Pro, HSP Brontosaurus, Exceed Infinitive,...

Customized to perfection with cutting-edge technology from 3D Slash.

Designed specifically for individuals seeking a unique and personalized experience, Human is now tailored to perfection with the innovative capabilities of 3D Slash.

The Hydraulic Axle Platform is designed to transport extremely heavy loads of up to 1000 tons. It features a well-engineered rigid frame and hydraulic oil-operated system. Additionally, the platform has separate drive and suspension systems for...

Begin by using a 3mm drill to prepare the hole for the pivot mechanism and run a 7.2mm bit for a snug fit around the stub axle area since printing with certain materials might leave this part a tad loose until warmed up to make fitting easier then...

Crafted with precision using the cutting-edge technology of 3D Slash!