traxxas rustler rear wing 3d models

Rear body mounting pilar

It's the measurement from the original part. ... Internal-splined half shaft for Traxxas Slash 4x4. ... MODEL# 6853A.

The rear strap was a piece of cake - all I needed to do was use the center screw from the spoiler. Easy peasy! However, the tabs did give me some trouble. The hole is probably a bit too small, so I had to use needle-nosed pliers to coax the pin...

I used a 3mm screw, washer and nut to hold the strap in. For the rear strap, I just used the center screw for the spoiler. The tabs were a bit difficult, because the hole is probably a bit small, so I used needle nosed pliers and had to wiggle the...

I remixed it a bit bcs. ...the front one broke two times this one is still good after a lot of bashing ;) also can be mounted very easy without unmount anything except the two screws back mount for 3mm LED with or without metal, front mount for 5mm...

Mounts are designed specifically for installation at the front of the vehicle.

Customized version of https://www.thingiverse.com/thing:5545010 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5545010

The entire system requires the full model for accurate assembly. Individual components can be referenced, but printing individual parts may result in a malfunctioning unit. ...Only the specific parts listed as printable files were designed by me and are...

Make sure you mirror this before printing. This is a remix of Mike_44 Bell Crank design. Iv'e reinforced it the place where mike_44's design snapped on my Rc car 2 times. This bell Crank will require a small modification to the shell of the...

I remixed it a bit bcs. ...the front one broke two times this one is still good after a lot of bashing ;) also can be mounted very easy without unmount anything except the two screws back mount for 3mm LED with or without metal, front mount for...

da ich sehr unterschiedlich dicke LiPos benutze und mich der Standard Halter genervt hat, und für jedes kaufbare Kit Löcher in Chassis müssen, habe ich mir selber was designed ;) ich habe jetzt noch keine 10m Sprünge damit gemacht, aber beim...

This is my batt cage for a custom MM build I've done.Designed around a CHNL 6200mah 3S battery with a 400MM velcro strap.Some time I'll post pics on how the heck you're gonna use this thing(Credit to me for the awesome MM name thing.)(Edit 4-7-24)...

Customized version of https://www.thingiverse.com/thing:5545010 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5545010

Perfect mount for a spare body, or the main one, if you don't mind to cut the hole in to the windscreen. ...Much better weight distribution than with the GoPro mounted at the back (there's also back mount visible on pictures).

Xmaxx rear mud guards with clamps.

Here's a custom, two-piece roll cage designed specifically for the Killerbody RC car body on your Traxxas Slash 4x4. ...This sturdy structure requires a simple glue-together assembly and secure mounting using four small screws directly to the body.

This unit is a direct replacement for the rear body mount on your vehicle.

The Traxxas Lataxx has a +1 degree toe adjustment which adds +2 (+3) degrees of toe. This modification enables the vehicle to straighten out sooner when exiting a corner on full power. I'm printing this model using PTEG. Enjoy! Important Note: This...

Use the pickup version on the original Traxxas TRX-4 Sport body or other pickups. Use one stock shock mount screw plus two more on the chassis, also a zip-tie can be used to reinforce but not required. 314mm wheelbase, cannot be used on larger...

Designed these arms to get my old-school Traxxas Bandit down to a ride height closer to modern buggies without cutting springs or travel limiters. These have 1.5 degree hinge pin angle at the outboard for a total net of 3 degrees of toe in- just...

The TRX-4 rear high body post stands at 54mm, 97mm, and 107mm tall, making it a breeze to print with the least amount of supports required.

Racecar rear wing plane with Gurney flap and mounting brackets

Rules Governing Rear Wings in the Year 2018

For Amusement - The Rear Wing of a Formula 1 Vehicle

SF90H Rear Wing - Basic FEA using 3D model by: Marius ImiolczykFormula 1 Rear Wing 2019: Design & CFD-Simulation

Kenner B-Wing Rear Cockpit - Partie arrière du B-Wing de Kenner

While sacrificing some scale detail, it makes up for this loss in added rear clearance, ideal for tackling near-vertical obstacles. The design prioritizes protection of the rear edge of the stock body shell while minimizing visual impact. The body...

A friend downloaded an LCG rear tower from here and the screws were off + they forgot the tie rod mounts lol, So I designed this instead. This actually fits properly and has much more adjustment available. Enjoy Check out our website!!!

This design replaces the stock rear axle in the Trx4, paired with a front axle. I used a shorter servo arm similar to the one shown from Losi, along with a tie rod I had on hand from my Bandit drag car conversion. If you print this, please share...

Rear equipment bay mount plate for a Matek Wing FC in a Stealthwings raphax.