traxxas rustler 2wd rear wing 3d models

This design is tailored specifically for a Traxxas Slash 2WD, allowing users to reverse-mount the transmission for improved center of gravity and cornering capabilities. Alternatively, it can be installed in its original configuration. ...The design's...

I designed these mud guards for a Traxxas Slash 2wd High center of gravity chassis to keep the dirt out of the chassis. It uses the holes from the nerf bars so you will need 4 screws that are a bit longer to replace the ones from the nerf bars. ... ...

To secure the fan mount, replace the original screws with three twenty-five millimeter button head screws, similar to Traxxas #2581, since the mounting wall is two millimeters thick and the original screws are only 23 millimeters long. If you don't...

Put a 40mm fan on your rustler. ...Needs 4 m3 screws 12mm long

Simple mount for mounting aftermarket ESCs like the Max10SCT in the Rustler.

This is a Traxxas Slash 2wd LCG Chassis - Sidewinder SCT ESC Holder Bracket and FS-RG3E Receiver Holder. The Castle Sidewinder 3 SCT needs two to three twenty-five millimeter screws to keep it in place securely. ... The FLYSKY FS-RG3E requires one...

It's also likely compatible with other 2wd Traxxas models, but some modifications will be necessary to get it to fit properly. The design draws inspiration from the new clip-on style straps featured on the Traxxas 4TEC 2.0 and TRX4. To install this...

However, it may also work with other 2wd Traxxas models after some modifications have been made. The design of this strap is based on the new style of clip-on straps found on the Traxxas 4TEC 2.0 and TRX4. To make use of this strap on your car,...

... ...This file comes with a strict condition: it cannot be used for resale purposes or to generate personal income. The accompanying image showcases the Rustler's camera mounting area, clearly illustrating where the GoPro mount should be installed.

Wahacze do Traxxas VXL komplet przód i tył Wypełnienie 100% Zalecany filament ABS

The new upgrade kit is designed specifically for the rugged Rustler 4x4, allowing owners to swap out smaller batteries for larger ones that provide more power and longer-lasting performance.

I designed a simple chassis saver for my Traxxas Slash 2wd with High Centre of Gravity chassis. The original design was made by Proline a few years ago to address the weak point where the transmission bolts to the chassis. However, when Proline...

This is a GoPro mount for the Rustler 4WD VXL - it might fit others but I've none to test with.It is intended to replace the roof bars, which are held on by four screws from inside the body.  I experimented with a few designs, but settled on this two...

This is a GoPro mount for the Rustler 4WD VXL - it might fit others but I've none to test with.It is intended to replace the roof bars, which are held on by four screws from inside the body.  I experimented with a few designs, but settled on this two...

Body Mount Extension as Add-On to the original Body Mount of the Slash 2WD to fit the Proline F150 1979 body in the front. ... Built with Tinkercad.

... ...The piece prints in two halves without support if pointed up vertically with the interface line touching the build plate. Use 100% infill. The wing mount is for an Arrma Kraton 4S wing. ...Two M5 bolts go through the holes for increased stiffness.

... lower back on the build plate with 100% infill. The wing mount is for an Arrma Kraton 4S wing. Two M5 bolts go through the holes for increased stiffness. ...The Red body pictured was a first attempt the Blue body has added cooling ducts and vents.

A 3D printable 90 tooth spur gear for 2 wheel drive Traxxas models. ... https://www.youtube.com/watch?v=LV5MNS3CUnk

wheelie bar for traxxas drag slash use m3x16mm screws these could be used for show or as templates to fit bodies

Here is a link to the product page for the real part: https://traxxas.com/products/parts/3632A If you look at the model from the bottom up, the caster block on the right is the actual right caster block, and the one on the left is the left caster...

Here's a quick and simple mount I came up with so I could run Jato rear shocks on my Slash without sacrificing ground clearance. I mounted my body mount on the front side of the shock tower, so make sure to factor that in when building yours - this...

Rear Wing with Three Elements

rear wing of formula one cars.material: ABS plastic.

Battery strap for Traxxas 2WD Rustler. I added a retaining clip to hold the wires and balance lead so they don't flop around. ...There are 2 files - one has a spacer underneath for thinner batteries and another without a spacer.

The wing insert for the new traxxas sledge. There is three different versions. ... You can use factory hardware no need to get new hardware

The Final Piece: "Do You Need Downforce?" The Perfect Rear Wing with an Integrated Amazing Air Sucker! ... Hold the Platform in the Perfect Position and Screw it On!

The backside aerodynamic element, commonly referred to as the rear wing, plays a crucial role in enhancing vehicle stability and performance by controlling airflow and providing downforce.

Fits the Traxxas Sledge RC Truggy. TEST VIDEOyoutu.be/hIVh-Q1ImEU Aditional Hardware (Optional) This wing mount can be installed with the original hardware but it is recommended to use longer screws and lock nuts. ...Two 4x25mm screws  Two 4x35mm screws...

A rear bumper for the Traxxas Maxx RC truck, designed to perfectly complement its impressive front counterpart, is now available.

... your Traxxas Slash, they can be found here: https://www.youmagine.com/designs/traxxas-slash-bumper-arm . A support brace for the rear bumper arms is also available at the same link: https://www.youmagine.com/designs/traxxas-slash-bumper-arm-brace.