traxxas phone mount 3d models

... achieve optimal results, it's recommended to print supports at a 45-degree angle with 2mm spacing. 5/20/19: A V4 version of the mount has been introduced, featuring a strategically placed cutout for improved wiring organization and reduced clutter.

This is a motor mount designed specifically for the Velineon VXL-3S system, featuring a durable 20mm fan to keep components cool and efficient.

The E-Revo 2.0 wall mount securely holds the car in place, its retaining clip expertly pulling the vehicle firmly against the wall to prevent any potential roll-off caused by the car's substantial weight on the wheel mounts.

You will need an m5 nut(non-locking) and an m5 bolt although one is included in the stock mounting hardware for the GoPro Place the smaller part's base in hot water for a few minutes before placing it into the hole and you should get a perfect fit...

Just a flat plate for mounting just about any ESC into the HCG slash chassis, I was able to fit a GoolRC 3s ESC off Ebay onto it without any issues.

Mount the front battery support now! I've got a sweet 1500mah Lipo 3S ready to go. Share your thoughts and ideas in the comments below - looking forward to hearing from you! ...Cheers, Daniele.

The attachment point for the mount resides on the left-hand side of the framework, proximal to the fuel door location (please refer to accompanying photograph). An additional upper segment serves to extend the camera positioning, allowing it to be...

Once printed, simply press an M5 nut into the hexagonal recess (it should be quite a tight fit, so it doesn't fall out), then attach your gopro to the mount using the standard thumbscrew that comes with your gopro. This mount then simply clips onto...

A Front Bumper Mount Ring: An Improved Version This is an enhanced version of the original design found at https://www.thingiverse.com/thing:394116 (V1). ...The main goal was to create a ring that sits snugly and closer to the front bumper, preventing...

I tried two ready mounts, but neither was good enough (the camera bracket came off after a jump, or the maker's position was not OK) so I made my own. I built everything from scratch, but JF_Chabot design influenced a bit my project, so I mark my...

I tried two ready mounts, but neither was good enough (the camera bracket came off after a jump, or the maker's position was not OK) so I made my own. I built everything from scratch, but JF_Chabot design influenced a bit my project, so I mark my...

*Important - to do this mod you need to cut the two tabs off that slide into the stock servo mount. Once you do that there is no turning back as the stock servo mount will no longer work and the piece you are cutting is part of the axle. I just...

Nitro Traxxas Revo Front Body Mount Replacement

Hobbywing MAX6 mount for Traxxas XRT

Traxxas T-Maxx 6S motor mount

Traxxas Rustler 4x4 Rear Bumper Mount Part Number: 6737

Traxxas T-Maxx Classic 4S-6S Lipo mount

Human mounts e-maxx on traxxas flux tork hpi.

Runcam 2 front mount for Traxxas X-MAXX

This is a Traxxas Telemetry Expander 2.0 mount, for mounting on the T-Bar of the Traxxas Sledge.

This is a ESC mount for a MAMBA X ESC in A Traxxas MAXX.

Replace with TRAXXAS 8215 - Body Mount. ...The latest upgrade to lift the TRX6 Body higher.

Replace part for TRAXXAS 8215 - Body mount. ... Higher and firmer version to raise up TRX6 body

Rear Bumper mount Traxxas X Maxx Picture shows Front but its REAR

esc mount, to mount an aftermarket esc into the stock location of the traxxas 1/16 vehicles.

Front led mounts for the Traxxas Rustler 4x4 VXL. ... Used 6 LEDs 5 mm For mount need 2 screws m3x10.

This is to securely mount the Hobbywing Max8 power switch to the center chassis brace on the traxxas Maxx

this is a esc mount for the new traxxas xrt rc car that i made on fusion 360.

I retrofitted my old Kyosho Optima with a traxxas XL5 ESC. ...This will mount it vertically in the servo tray

This is an esc mount for aftermarket esc's for the 1/16 Traxxas Revo, Slash, Summit and Rally.