traxxas jato parts 3d models

Battery compartment designed specifically for Traxxas vehicles like Stampede, Rustler, Monster Jam, Big Foot, and Bandit models.

A rear bumper for the Traxxas Maxx RC truck, designed to perfectly complement its impressive front counterpart, is now available.

A simple sidebar replacement for the Traxxas X-Maxx. ... Designed it together with the wheel rims for optical enhancements.

A replacement of wheely bar wheels for traxxas models. ... I made two sizes: 25 and 30 mm

Today I am adding another project, which is replacing the bodywork clips with nuts. ...Project made under Traxxas Summit.

traxxas phone holder for TQI you will need 2 bolts and nuts remix of https://www.thingiverse.com/thing:4694593

Upper LED bar for Traxxas Xmaxx, mounting clip with socket, holes and adapters for 10mm LEDs, battery compartment.

I initially thought about buying one of these one-way clutches from Traxxas, but then I discovered that they had changed the shaft size from 6mm to 8mm. This led me to create this adapter that fits a standard 12mm one-way bearing, solving this issue...

... is only feasible for the rear A-arms due to steering interference on the front. The part's weak point lies in the four holes where the pins attach the A-Arm, requiring precise printer settings to achieve optimal layer formation and highest strength.

Two strategically positioned holes run through the center of this robust part allowing for an extra stabilizing feature, an attachable middle brace that enhances overall structural integrity. Perfect for users wanting to upgrade with added support...

Traxxas extra rx case - Still Waterproof - Need 3x M3x35mm screew - Highly detailed - All parts are separate objects - Fully ready to 3D Printing - Clean and non-overlapping topology - Model is settled to 0,0,0 XYZ Axis - Make the right size for you...

Parts 1 and 2 are closely matched, so be careful with the retraction process or they won't fit together properly. You may need to use a mallet to tap them into place. For added durability, consider printing parts in PETG material. To assemble the...

Traxxas 1:10 Servo Saver I was impressed by the design of AtomKemp's servo saver, but unfortunately it wouldn't fit on my Traxxas Rustler. I made some modifications to make it work with 3mm holes instead of .5mm. This should be compatible with any...

... is more to your needs. When fully assembled (3 parts) it measures 191mm x 123mm and is 140mm high. Each part prints very easy with no supports needed. I printed mine at 0.3 layer height (draft) and 20% infill. ...I used 2mm walls for strength.

--------------------------------------------------------------------- Required parts: * The printed parts: Mudguards left / right + 2x clip + 2x spacer * 2x M3 x 20 mm countersunk screws * 2x M3 x 12 mm screws * 2x M4 x 8 mm screws Mounting: First...

... needed. 100% infill is recommended for maximum strenght since it is a drivetrain part. With this thing in my gearbox the summit has a play on rollout about 5 cm total! with stock part it was more than a half meter(50cm). ... Category: R/C Vehicles

... the Rear of the A-Arm. To Build the Strongest Parts, Users Must Focus on Maintaining Precise Printer Settings to Ensure Proper Layer Formation Around Critical Pin Holes. ...This Helps Minimize Weak Points and Achieve Maximum Structural Integrity.

These are extended body posts for the traxxas slash or other vehicles that use posts that have a screw hole on the bottom of the post

A 54-tooth, 3-spoke wheel is specifically engineered for use on grass and soft terrain, and it's tailor-made for the Traxxas Rustler RC vehicle.

The wing insert for the new traxxas sledge. There is three different versions. ... You can use factory hardware no need to get new hardware

The model now boasts a sleeker design thanks to tightened dimensions of the rear carrier, optimized specifically for the 1/10 scale 4x4 Traxxas Slash.

Get ready to upgrade your ride with this awesome Traxxas 12mm hub to 14mm hub adapter - it's a game-changer, trust us!

The Traxxas Slash 1/10 Scale Battery Adapter mounts snugly within the chassis without issue, fitting perfectly in its designated space.

allows you to control your model with one hand, fits the traxxas tqi controller, may fit other steering wheel type controllers but i havent tested any

Updated with the latest aesthetic redesigns rear axle housing available now for all serious racers handling the robust 1/10th scale all-terrain monster truck, Traxxas Slash.

rear turrets for traxxas trx4 sport high bodies, I printed them with 100% filler, the car has had many accidents and they have never split.

Replacement for the default Traxxas Nut-Tool. ...Designed to be usable for the X-Maxx as well as the E-Revo with some larger handles.

This is a simple base for mounting a different ESC than the Traxxas Maxx came with. ... It uses 2x m3x5mm flat head counter sunk screws to mount.

Printed from Soft PLA. ...Protects the front upper control arms on the Traxxas Summit 1/10. ...Secures with zip tie to the lower control arm.

This product is specifically designed for compatibility with the Revo-style bumper and the Traxxas 4x4 chassis, ensuring a seamless fit onto the front differential housing.