traxxas backslash 3d models

I needed a way to stiffen the shocks on my Traxxas Bandit for use in a Mouse Droid, so I came up with these. Print with supports underneath and several shells for strength. EDIT: I added a couple of longer ones for those needing stiffer springs. ... ...

A pair of sturdy stands elevates the Traxxas TRX-4 Series chassis, relieving pressure on its tires. ...The front steering hubs securely rest in the front stand's saddle-like design, while the rear stand folds up and cradles the bottom of the portal hub...

I modified SCACE OF SPADES driveshaft to actually fit into my traxxas slash 2wd. To get the best results scale to 99% and print at 15 degree angle. ...It has held up well and is very quick and easy to print.

The Traxxas UDR Panel comes pre-assembled and is an easy install that takes no more than about 15 minutes. You can mount it on a flat surface or attach it to your vehicle with the screws provided. ...The panel gives you access to all of your vital signs...

This is an updated design for the truggy stand used with the Traxxas Unlimited desert racer, adapted to print upside down on two sequential STL files labeled first and second. The result gives the appearance of lettering inlaid into the surface. ...It's...

Updated design now available featuring a rear bumper specifically designed for the 1/10 scale Traxxas Slash. This bumper is intended to be used in conjunction with my printable bumper arm, which can be found at Thingiverse under the ID number...

the lower shock spring support for the suspension on the 1/10 scale traxxas slash. version with shield http://www.thingiverse.com/thing:1175692 Print instructionsUnassociated tags: r/c Category: R/C Vehicles

Nothing Special, fits Traxxas 2.4GHZ TQi Remotes (the newest version). If your name is Brielle, you're in luck because you have a customized version available to you with your name on it. ...If not, choose the basic one, OR represent my little sister on...

This modified body mount is specifically designed for the Traxxas Stampede 4x4 VXL. It lowers the body just enough to prevent obstacles like snow, mud, rocks and other debris from getting inside. ...Version 2 of this design prints easily with minimal...

Store the Traxxas Tire Glue bottle and two nozzles in one place. I designed it as a tight fit, so bottle and nozzles can't fall out. ... If it is to tight/big for you just adjust the scaling in your slicer a bit for x/y dimensions.

this is a replacement support piece for the chassis of the Traxxas Stampede RC truck. I've made it more robust than the original and printed with ASA for improved strength. I designed it so you can print it on it's side but you'll still need some...

I'm displaying some of the plastic body parts for a Traxxas Rustler that I measured with a dial caliper and ruler, then modeled in SolidWorks. ...The parts aren't entirely precise, so if you print them, they'll need some sanding and/or drilling to...

Traxxas Bigfoot Chassis Addition - Spans the Chassis above the battery, effectively creating a 2nd floor or shelf above the battery for mounting additional hardware. ...Item can be bolted to the chassis by drilling 4 small holes into the chassis and...

I designed an upgrade for the shocks on my Traxxas Bandit to enhance its performance in a Mouse Droid, so I created these. ...They can be printed with supports underneath and multiple shells for added strength.\r\n\r\nUPDATE: I have since added longer...

Printed for a Traxxas Slash 2wd. The 4x4 setup is a distinct configuration. This one doesn't utilize bushings or bearings, which may cause it to wear out rapidly. However, it appears to hold up remarkably well nonetheless. ... Thanks for the...

traxxas wheelie bar fits all 2wd models whats needed; m3 x 20mm screw ( shorter may work also) would not recommend for hard jumping Printed on ender 3 pro PLA ploymax 218 C 60C bed temp 65 Speed 5 to 6 walls 80 infill

I needed a custom male battery connector to power my Traxxas batteries in a new project without delay. ...Rather than waiting for a store visit, I decided to fabricate one myself using spare parts from an earlier endeavor, which fortunately included the...

I'm combining two Traxxas Ski files, tweaking them to prevent flips and scaling up the ski for increased surface area on the snow. Theoretically, this mod should improve stability and control. ...If you're feeling adventurous, give it a shot and share...

EDIT: Upgraded with advanced new design bumper arm for 1/10 scale Traxxas Slash. Two holes in the middle of the part are specifically designed for attaching an additional center brace to boost support. ...This extra mounting point allows for secure...

This Traxxas rubber tire has a wheel diameter of 2.8 inches (71mm), is 2 inches wide, and boasts an overall diameter of 3.8 inches (91mm). ...Although the part's dimensions may not be entirely exact, they are quite close to the actual measurements taken...

... Schrift nach außen extrudiert damit man diese im nachhinein noch anmalen kann. Und den Verbinder hab ich auch noch neu gemacht Du brauchst: 1x Rechtes Seitenteil - Traxxas 1x Linkes Seitenteil - Traxxas 2x Verbinder 2x Drucken 8x M3 6mm Schrauben

A standard-sized wheel is offered for Traxxas/Latrax TQ radios to replace the smaller TQi version. This larger wheel was custom designed by someone who prefers it over the new, smaller option. ...Additionally, a file for the buttons on current TQ models...

This is an accurate model of: Traxxas part # 2742X Interestingly, it's made up of two separate components, with exactly 0.003 inches clearance between the ball and its housing at a scale factor of one-to-one. ...However, this gap exceeds the actual...

This is a precision-crafted Shifter "gear" engineered specifically for the 1/10 scale Traxxas Summit. Designed to eradicate the colossal amount of slope inherent in the original drivetrain, this component is intended to provide a seamless fit. Here...

it has the normal mounting holes in the front for the shock, but it also has mounting holes in the rear so you can mount another shock to the rear of the a-arm (for the rear a-arms only, steering gets in the way on the front) using my printable...

I have lost the battery clamp for my Traxxas R/C car. So I made this one using Thinkercad.com and printed it on my Snapmaker A250 using Luban software. It's not exactly as the original one but it holds the battery in place as required. I used PLA...

This is a FPV camera mount to place a small AIO camera on the frame of my Traxxas TRX4M Defender. It positions the camera to look out the windshield and give a FPV driving view. The camera is mounted using foam tape and powered off of the receiver...

Traxxas Rustler Receiver Box Unboxed and Ready to Roll Out Inside the Traxxas Rustler Receiver Box, you'll find a treasure trove of high-quality components that bring this rugged off-road truck to life. The first thing you'll notice is the sturdy...

This mount was made to swap out the old ESC mount for the new Velineon VXL-3M that can be found here (https://traxxas.com/products/parts/escs/vxl3m). Added notches to the plate for the locator tabs on the bottom on the ESC with a bracket to hold it...

Updated with a fresh design, this is a rear bumper tailored specifically to the 1/10 scale Traxxas Slash. For optimal stability and alignment, it's highly recommended that you use it in conjunction with my printable Bumper Arm, available on...