traxxas backslash 3d models

Decided to create this design since you cannot buy them separately. ... Hope this is helpful to someone

Simple esc mount and gnss for slash lcg 2wd chassis. If you found this, no explanation is needed. ...Enjoy!!

A Fresh Hex Hits My Ride's Axle Hub, Perfect Fit for 5mm Rods - Just What I Was Looking For

This is a redesign of bobcatfr63, I was getting a bad scraping noise with the spring rubbing the sides of the shield. I shrunk down the front and also made it a bit larger to cover more of the spring. This object was made in Tinkercad. ...Edit it...

<p>This mount/bracket allows you to keep the entire antenna mounted under the body of the slash. It just clips on to the chassis. It also has an eyelet that allows for you to attach a tether to the battery retainer clip. It is best to print upside...

printer temp for me was 210C, but that can vary from person to person. PRINT BED MUST BE 90-95C or extreme warping occurs. I let it print the first 1cm then super glue the edge to the glass build plate in multiple locations. place glue, then gently...

printer temp for me was 210C, but that can vary from person to person. PRINT BED MUST BE 90-95C or extreme warping occurs. I let it print the first 1cm then super glue the edge to the glass build plate in multiple locations. place glue, then gently...

Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following settings: m3_nut_depth = 2.7 no_of_nuts = 1 nut_angle = 90 pulley_t_ht = 5 idler_ht = 1.5 profile = 9 retainer...

I'm happy to report that the machine is up and running with precision-tuned options for customized fabrication. Customizer technology, available at http://www.thingiverse.com/apps/customizer/run?thing_id=16627, made this possible. Below are...

Human: Customized Version of Thingiverse Object Number 16627 Created with Thingiverse Customizer - http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the Following Options: Motor Shaft Diameter =...

Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16627 Using the following options: nut_shaft_distance is set to 1.2 mm m3_dia is specified at 3.2 mm additional_tooth_width is adjusted by 0.2 mm...

this mod is to use any 1:10 hex wheel instead of the genuine one. place this inside the rc wheel and push it gently onto the transmitter steer axle. ...

Magnetic Mounting System with Integrated Front Body Kit

not printed yet... will update. may need to check the scale. ...but should be 3.66" x 3" x 2.56"

<p>A component of the parts kit 3768. &nbsp;It is a cone shaped lower spring retainer for my 4x4 Rustler vxl. &nbsp;</p><p>I got my ruslter and took it out for a spin. &nbsp;It collected every kid in the neighborhood! &nbsp;An hour later after they...

This creation is proudly crafted with Tinkercad, a fantastic tool that lets you edit and refine your designs right within the browser - check out the link at https://www.tinkercad.com/things/k5m6rBc7CkO.

This thing was crafted with precision using Tinkercad's intuitive design tools. ...Edit and refine it seamlessly at https://www.tinkercad.com/editor/1f3T2pBd4bX

This connects the servo to the wheel hub, functioning flawlessly on my setup.

I had to reorganize the layout when I installed the Mamba Monster motor and ESC, and ran 6S for speed runs. Now that I've completed the speed runs, I needed to create a more conventional setup. Thanks to the large ESC provided by Mamba, this meant...

I recently upgraded my trusty Maxx truck's bumpers, which were in dire need of replacement after I purchased it. To start, I fabricated custom bumpers that would perfectly fit the vehicle, giving it a fresh new look. The front bumper now boasts a...

Need a Holder for the 3S 5000 Lipo Akku, Original was only for a 22mm Akkus,The new one has 35mm so I have to buld my own one.

Hi, maybe you could not wait for online shopping delivery, so here you are ! ... hope be useful.

The Human has been downsized to match the dimensions of Maxx's diminutive sibling, the Maxx Jr.!

I upgraded my revo with a brand-new body that failed to match the old, compact post style. Therefore, I opted to fabricate a custom version myself. ...You'll find two models - one extended and one compact - suited to accommodate various lift...

Pro Line Body Holders require caps to be fitted. Using a soldering iron, an EPT stud (or screw) must be driven into each cap until fully seated and level with the outer edge of the body clip. This insert has metric dimensions: Thread type: Unified...

Hello All, This is the first design that i'm putting on here. Just wanted tot attach my sons GoPro to my Mini E-revo. So i started playing around in Fusion 360 and this came out of it. If you like it feel free to use it. Please just click the...

A 70T spur gear, compatible with<|im_start|>er the<|im_start|>urse<|im_start|><|im_start|>ur Rustler or T-Maxx vehicles, features a 32P nitro drive mechanism. ...This high-quality component ensures efficient power transfer and enhanced performance for...

A custom-built Nitro Rustler model features a fresh body design, along with an adjusted wing mount and wing installation for optimal performance.