traxxas 3s rustler 3d models
7143 3d models found related to traxxas 3s rustler.
thingiverse
Here are the 0.85" wide "Pizza Cutter" rims and tire that match my previously designed [rims on Thingiverse](https://www.thingiverse.com/thing:4049393). ...The part numbers should correspond to those rims, allowing you to easily pair the wide and narrow...
thingiverse
leider hatte ich keine Senkkopfschrauben, daher hab ich das sehr coole Design etwas angepasst ;) aber ich konnte einfach nicht aufhören zu designen, und darum gibt´s jetzt ein paar optionale Extras :D benötigt: Seitenteile für M3 ...
prusaprinters
<p>Just a couple of things to help me not lose body pins and to help pull the battery strap pins out easier. I printed them out of TPU and as much as I like the body pin straps, the battery pin tabs make inserting and removing the battery strap pins...
thingiverse
Customized version of https://www.thingiverse.com/thing:5545010 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5545010
thingiverse
Customized version of https://www.thingiverse.com/thing:5545010Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5545010
thingiverse
Here are some major updates for the project on 5/12/2015. A Stampede test run was conducted and impressively, it remained intact despite experiencing a few bumps along the way. Following this test, I revisited the .stl file and addressed various...
cults3d
leider hatte ich keine Senkkopfschrauben, daher hab ich das sehr coole Design etwas angepasst ;) aber ich konnte einfach nicht aufhören zu designen, und darum gibt´s jetzt ein paar optionale Extras :D benötigt: Seitenteile für M3 ...
thingiverse
I've got a couple of tricks up my sleeve to help prevent losing body pins and make removing battery strap pins a breeze. I printed out TPU for them, and let me tell you, they're a game-changer - especially when it comes to those pesky battery pin...
prusaprinters
Here are the 0.85" wide "Pizza Cutter" rims and tire that go with the rims I designed here. ...The numbers should correspond to those rims, so you can match the wide and narrow rim design.I'm lazy, so I am not going to upload any pics here, but you can...
grabcad
Transform your old Traxxas Nitro Rustler into an electric ride by fitting a battery tray and motor mount in its existing chassis holes. Although the transmission brace and top plastic tray need slight modification, installation is straightforward.
thingiverse
This is a custom steering bell crank designed specifically for an electric-powered two-wheel drive (2WD) Traxxas Rustler. The part should fit seamlessly as printed, and while smoothing out any rough edges can enhance its performance, it's not...
thingiverse
Center skidplate and rear bumper designed to work with the 2wd traxxas rustler or bandit chassis. Rear skid only will maybe fit the other 2wd models. designed to use a rpm wheelie bar mount to stiffen it up is recommended but it isn't required.
thingiverse
I built a rear body saver for my trusty old Rustler body, which had been taking quite a beating from those rough landings. As I tossed the truck around, its frame began to show signs of stress, with cracks starting to form. ...To prevent any further...
thingiverse
when using a lipo battery on my rustler vxl I could never keep the front wheels on the ground, I tried a wheely bar but it keeps breaking off so I designed an extension that would move the CG forward to keep the front wheels on the ground
thingiverse
Human: Customized version of http://www.thingiverse.com/thing:666162 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=666162 Instructions Using the following settings: Numerical slider set to: 1 Numerical slider set...
thingiverse
Redesigned the LED Ring bracket to fit the 3S version of the Granboard, works with Lt_AldoRaine's Dartboard LED Ring: https://www.thingiverse.com/thing:4753272. Brackets are extremely tight snapping to ring and board and hold very well. Also look...
thingiverse
RC nárazník jsem vyrobil pro svůj model. ...Je to první návrh model se pořad vyvíjí. Pro model Traxxas Rustler
thingiverse
Someone requested I create a small holder to store their shorty pack in the stock battery tray of a Traxxas Rustler. This device needs to accommodate a battery with dimensions 96x47x25.5mm. ...If anyone else wants me to design a configuration for them,...
myminifactory
This is a four-piece wing designed for the Traxxas (1:10) / scale Rustler 4X4. If placed diagonally on the print bed it will print on the Ender 3 and other printers of a similar size. For best results print the wing using PETG or CF-Nylon and the...
thingiverse
This is a small clamp/bracket which fits over some 3rd party rear axles for the Traxxas Rustler and slash. See the photo and link below for the metal 3rd party axles. These axles will fall apart when mounted in the car but with these spacers they...
thingiverse
The Strengthened Rear Carrier for Rustler bolts in the same parts as the original. the part is stronger with some extra bracing and making it thicker in places where it does not interfere with the normal operation of suspension and drivetrain. ...
thingiverse
A basic working front shock tower for the 4x4 version of the rustler. I am very new to designing and 3d printing (this is like the fifth thing I have ever printed). But it seems to be just as strong as the stock one if not stronger. I don't know how...
thingiverse
Battery Retainer for Traxxas Rustler 2WD, should also fit Bandit and Stampede 2WD. ... Ideal for 2S LiPo Hardcase or 6-7 Cell NiMH Stickpack.
thingiverse
Good for Traxxas Bandit vxl, Bandit, Nitro rustler, Rustler vxl, rustler, Nitro slash, Stampede vxl, and stampede.
thingiverse
This model is crafted using Tinkercad, an innovative tool for 3D design and fabrication. ...You can easily modify or edit this creation online at the official Tinkercad website: https://www.tinkercad.com/things/6eZDDHEOY7u