traxxas 3d print
2656566 3d models found related to traxxas 3d print.
thingiverse
This is a very close 3D replica of the Traxxas TRX-1 chassis. This would be a little difficult to print but I guess it could be attempted with a carbon fiber filament. The main issue would be the strength of the front chassis kick-up. A better...
prusaprinters
I've installed this in my Rustler and it fits perfectlyHere is a link to the product page for the real part: https://traxxas.com/products/parts/3632AIf you look at the model from the bottom up the caster block on the right is the right caster block...
thingiverse
I made this for me and my friends traxxas slash's because we all had the problem of the black top coming off so I made one, to install place a small amount of scotch tape over the top of the antenna then place just a drip of glue into the 3d printed...
thingiverse
Anyways I had to get a new pinion, but there aren't any 48p 5mm bore pinions, which meant I had to buy a different pitch pinion, which also means I had to buy a new spur gear to match, but there also isn't any traxxas spur gears for my car with...
thingiverse
:D Get the entire file at: https://cults3d.com/en/3d-model/gadget/traxxas-stampede-strong-bulkhead OR: https://www.cgtrader.com/3d-print-models/hobby-diy/other/traxxas-stampede-strong-bulkhead The bulkheads on the Traxxas Stampedes always seem to...
thingiverse
Printed from Soft PLA. ...Protects the front upper control arms on the Traxxas Summit 1/10. ...Secures with zip tie to the lower control arm.
cults3d
rear turrets for traxxas trx4 sport high bodies, I printed them with 100% filler, the car has had many accidents and they have never split.
thingiverse
These are designed specifically for the 4x4 Traxxas Slash, engineered to tackle packed snow with ease. ...Print two sets to ensure proper coverage for all four wheels.
thingiverse
I designed this specifically for the Traxxas Revo 3.3 and printed it out. ...You can easily adapt it to work with your E-Revo too.
thingiverse
Traxxas Stampede Chassis, This is an experimental part, and may require modifications, Print at your own risk Would suggest at least 80% infill
thingiverse
... it on my Snapmaker A250 using Luban software. It's not exactly as the original one but it holds the battery in place as required. I used PLA but I think ABS would be fine too. Feel free to modify ans share. P.S. I'm new to 3D printing.
thingiverse
Print Settings: Printer Brand: FlashForge Printer Model: Finder Rafting Required: No Supports Needed: Yes Resolution: 0.2mm Infill Percentage: 35-65% Overview and Background: The Traxxas Summit Mount is designed for the 1/10 scale Traxxas Summit...
thingiverse
This is a custom LED light holder specifically designed for the Traxxas Bandit, fabricated using 3D printing technology. To produce this design, I opted for a .2 mm layer height and achieved both pieces within a 30-minute timeframe. For infill...
cults3d
The bulkheads on the Traxxas Stampedes always seem to break, so it would be great to 3D print the replacement part and save the money when needed. I have tried other bulkhead 3D models and have tried designing one that is reinforced where the 3D...
thingiverse
Here are my optimized settings: Eccentricity multiplier: 0.9 Layer height: 0.25mm Infill density: 100% Printing speed: 40mm/s Support structures: enabled With these parameters, the amount of post-processing required was minimal. It's highly...
thingiverse
... HCG & LCG Chassis Stands. HCG is still a work in progress. LCG is complete and the bay has room for the Traxxas EZ Peak+ ID Charger. Support are required for the front opening. Supports for hexagons are optional. ...I printed with 20% infill.