traxxas 3d print

Chose to swap out the foam insert in the battery holder since the fresh lithium-polymer cells I had been using were noticeably shorter than the original Traxxas batteries.

Flywheel removal tool designed specifically for the powerful Traxxas 2.5 Nitro engine, perfect for the T-Maxx model. ...This innovative tool features three strategically positioned Hot Racing flywheel holes to ensure a secure and efficient flywheel...

I misplaced the clip holding my Traxxas Stampede's battery, prompting me to take precise measurements and design an alternative solution from scratch. ...The result is surprisingly streamlined, yet effectively serves its purpose with remarkable...

GoPro style mount designed to bolt to the chassis of a Traxxas Slash 4X4 (Not sure on 2WD) with recess under the mount to allow for a chassis protector / dust cover.

This is a body mount for a traxxas slash. It was used to change the body to a larger model. ...I belive it is about 77 mm ish, heavy on the ish.

Traxxas UDR Desert Racer Tail Light Requires 4 of These RC4WD 1/10 Baja Designs Squadron Pro LED Lights!! A Little Tinkering and Soldering is Still Needed to Get Them to Fit Perfectly !! ...And Finally, Some M2 Screws.

This is my upgraded Traxxas TRX-4 1cm lift kit, designed specifically to accommodate larger 2.2 tires on the trx-4. ... For successful installation, gather the following essential components: * 4 M3x18mm screws for secure mounting.

This is a modified version of the wing system for traxxas rustler by Kyle bedrich. I built it to suit my needs in my road car build. ... Use wing 3.0, as it requires no support.

This is a receiver box I designed for a 1/16 traxxas product; It will fit into the alternative servo mount on 1/16 e-revo, summit, rally, and slash models.

Traxxas enthusiasts can upgrade their TQi Smartphone Holder for any type of smartphone. ...To secure it in place, simply attach the holder to the rear screws of the remote control using a standard M3 x 35 mm screw.

The above image showcases a Traxxas Revo hollow rod end, designed specifically for a remote-controlled crawler project. ...It was meticulously crafted using SolidWorks 2015 software to ensure optimal performance and precision in operation.

... contributes to the overall appearance, it doesn't significantly enhance the bumper's strength. To mitigate this issue, I reinforced the bumper's structure and incorporated Micky ears to help stabilize it on the print bed during the printing process.

... or rough terrain driving. The upper arm is made from durable materials to withstand wear and tear, ensuring long-lasting performance. Upgrading or replacing the Traxxas E-MAXX's upper arm can significantly enhance the vehicle's handling and control.

Experience high-performance racing with the Traxxas Nitro Rustler/Sport, the ultimate remote-controlled car for enthusiasts! This powerful vehicle runs on nitro fuel and is designed for adrenaline-pumping action. With its advanced features, including...

same with the little clips - if you print them flat (a "U" shape, they'll likely be strong enough but they'll be even stronger if you print them standing up - I have yet to break one printed in either orientation however. I printed these with...

This is a somewhat water resistant RX box for the Traxxas Nitro rustler and Custom Mid-Motor Rustler builds. Before someone asks NO this is not waterproof unless you get some kind of custom rubber seal going. As always you're welcome.Last thing, this...

I suggest printing a couple at 8mm, and a couple of 50% scale on the Z axis for 4mm spacers. Print them with 100% infill, and they should hold up reasonably well. I printed mine with PLA, and they feel almost the same as the stock ones. ...PETG or ABS...

I created some water/sand tires (with hubs) for the Traxxas Rustler.This is a derive from another wheel on Thingiverse:https://www.thingiverse.com/thing:4566114However, I drew all tires and hubs completely from scratch using the tire and hub as...

Wall mount for the Traxxas TRX-4 and other similar RC trucks/cars It hooks around the rear axle of the vehicle and screws to the wall with two #10 wood screws (canada, not sure if there is a metric equivalent - 0.193"/4.9mm diameter thread). You...

It only holds the VXL-3S ESC and might not be compatible with all cars.I used a Traxxas Slash which gave me ample space, but other cars may not have enough room.Take care not to snap one of the screw holes off like I did because it's hard to work on...

The hole pattern fits Integy RC Model T8026 Steel Roll Cage Body for Traxxas 1/10 Slash 2WD. Though you can also mount it to the shell by drilling 4 holes. Also here is the controller mount. you can use it to attach an FPV screen to your...

... and taken with calipers. The Traxxas 1942 kit has short and long rod ends. This is the long rod end.The plastic has a hold for mounting to an M3 all thread for making your on suspension rods. ...The ball end has a through hole for an M3 bolt.

Traxxas 1942 short rod end for RC and hobby cars. This part is modeled in Fusion360 and the ball joint with limits is modeled. All major dimensions are accurate. Minor dimensions may vary slightly from actual dimensions, but all important dimensions...

After searching for a solution, I discovered that the necessary o-ring is only available as part of the complete Rx enclosure kit (Traxxas part number 7424). Fortunately, this kit isn't too expensive and was readily available at my local Hobbytown...

... and taken with calipers. The Traxxas 1942 kit has short and long rod ends. This is the long rod end.The plastic has a hold for mounting to an M3 all thread for making your on suspension rods. ...The ball end has a through hole for an M3 bolt.

Traxxas 1942 short rod end for RC and hobby cars. This part is modeled in Fusion360 and the ball joint with limits is modeled. All major dimensions are accurate. Minor dimensions may vary slightly from actual dimensions, but all important dimensions...

Hey, I want to share my Traxxas Nitro Rustler conversion with you! I myself did this to a 1995 Nitro Rustler. The motor mount itself doesn't fit perfectly but enought to work, which is why I am looking forward to your remixes. ...Have fun and enjoy my...

Lifted esc mounts are designed specifically for two-wheel-drive Traxxas vehicles. They elevate the electronics securely by 7 millimeters. The dimensions of these mounts measure 6.65 inches wide and 1.69 inches long. ...For a secure installation, it's...

Model of Traxxas 2.5R Nitro Motor. I have finished the outside appearance, however I am still in the process of refining the inside of the motor. ...I have the Piston, Crankshaft, and sleeve done, but I need to get the ports finished and the internal...

These two components form the essential part of the rear bumper attachment system in the Traxxas Slash, a highly versatile 1/10th scale four-wheel drive RC vehicle. ...I have carefully designed and incorporated an integrated hitch bracket onto the upper...