traxxas 2056 3d models

Led Mounts for Traxxas Rustler 4x4 VXL Vehicles. Works Well on Other Rustler Models Too. Used LEDs: GT Power 12x LED Lights. https://www.toemen.nl/power-12x-led-verlichting-set-wit-rood-oranje-blauw-p-25604.html Similar LEDs Available:...

This is a FPV camera mount to place a small AIO camera on the frame of my Traxxas TRX4M Defender. It positions the camera to look out the windshield and give a FPV driving view. The camera is mounted using foam tape and powered off of the receiver...

This is an essential part of the Traxxas Slash's wheels system. The hub cap securely connects to the bolts that keep the wheel in place. Currently, you need to use a screwdriver to carefully pry off the hub cap. I plan to make improvements to this...

This bumper is an extremely valuable addition to any Traxxas Rustler, allowing for precise control when drifting by effortlessly absorbing impacts from obstacles due to its generous cushioning. Its effectiveness is further amplified when printed with...

This is a miniature Cybertruck model engineered to complement the Traxxas Stampede 4x4. The Lexan windshield and cast acrylic side windows replicate the authentic look of the full-size vehicle, while the functional tailgate adds an extra touch of...

This fits a Traxxas Maxx and goes in the center of the rim. Version 2 fits a bit better. I used a 4 line brim. I sliced with Cura 4.8, originally I used the new beta Cura slicer, but it was almost impossible to remove the supports without...

This mount was made to swap out the old ESC mount for the new Velineon VXL-3M that can be found here (https://traxxas.com/products/parts/escs/vxl3m). Added notches to the plate for the locator tabs on the bottom on the ESC with a bracket to hold it...

Traxxas Rustler Receiver Box Unboxed and Ready to Roll Out Inside the Traxxas Rustler Receiver Box, you'll find a treasure trove of high-quality components that bring this rugged off-road truck to life. The first thing you'll notice is the sturdy...

Use as battery tray for XRT Traxxas. Infill 25% or less. I prefer TPU but PLA or similar will too to. PLA may crack on impact on jumps. Space under the tray for the straps. Nut holes are 4,5mm deep so you can use self-locking nuts. ...

GTR shock spring retainer for Traxxas #7561 and #7462 Print setting:Filament: PETG is recommended but PLA is workableInfill: Gyroid, 15%Enclosure: Not required Please let me know if there's any question in the comment section to help me improve the...

Spoiler wing for a Traxxas Latrax Teton. Mainly for aesthetic looks. Just need to line it up on the body, mark the holes, drill, and bolt on. I used standard M3 screws found on a lot of RCs, especially crawlers. If you liked the design, leave a...

Here's an updated look for your Traxxas Slash, just a little something to give it some personality. You will find all of the assembly details below: First off, fire up your printer and hit print on both pieces with 100% infill - don't worry about...

This is a custom LED light holder specifically designed for the Traxxas Bandit, fabricated using 3D printing technology. To produce this design, I opted for a .2 mm layer height and achieved both pieces within a 30-minute timeframe. For infill...

Here are some 3D modeling creations I did for the Traxxas Slash. Each part has been thoroughly tested and pushed to its limits on several Slash models. Some components perform exceptionally well in specific materials, such as nylon, which is ideal...

This design is tailored specifically for the Titan 12T motor used in the Traxxas Slash 2wd. I'm not aware of any other motors it may be compatible with. Print this model using a 10% infill setting without generating a raft or supports. After...

This is a replacement body post for Traxxas models (and probably others) that uses a screw-on thumb cap instead of the body pins. It requires a 30mm M3 screw that comes up through the bottom and goes all the way through the post for strength. This...

Updated with a fresh design, this is a rear bumper tailored specifically to the 1/10 scale Traxxas Slash. For optimal stability and alignment, it's highly recommended that you use it in conjunction with my printable Bumper Arm, available on...

I designed this bottom plate as a cradle for utilizing a two-speed transmission from a Traxxas Summit in an Axial SCX10. This version is specifically tailored for use with the Axial OEM U-frame. Notably, the mount for the shifting servo requires some...

:D Get the entire file at: https://cults3d.com/en/3d-model/gadget/traxxas-stampede-strong-bulkhead OR: https://www.cgtrader.com/3d-print-models/hobby-diy/other/traxxas-stampede-strong-bulkhead The bulkheads on the Traxxas Stampedes always seem to...

The bar with and without the flat panel is the VTx antenna mount, one version just holds a bulkhead SMA connector, while the other also holds a standard 30x30 PDB to make wiring FPV and other things simple (Outdated with the use of the Traxxas Light...

I initially thought about buying one of these one-way clutches from Traxxas, but then I discovered that they had changed the shaft size from 6mm to 8mm. This led me to create this adapter that fits a standard 12mm one-way bearing, solving this issue...

Thumb Control for Traxxas Radios is Now Complete. A First Version Has Been Achieved Despite Some Minor Flaws. The Knob Is Slightly Off and Short, But It Gets the Job Done. Further Improvements Are Planned To Enhance Visual Appeal. 7/14/20 Update:...

Borrowed our Traxxas TRX-4 show truck from work, and wanted to create a towhook/mount for it. Haven't printed it yet (the printer is currently working), but I think it will fit perfectly, and made a 3mm hole so you can make and mount your own type of...

I recently broke the plastic spur gears on my Traxxas 2075 servo, which prompted me to design my own replacement. You may need to carefully file the center holes slightly to ensure a smooth fit, but so far, mine is working efficiently. ... Keep in mind...

I purchased an extremely worn Older Traxxas Stampede. It initially featured a mechanical speed control system. The previous owner had upgraded it at some point to a high-performance ESC, yet he merely used zip ties to secure it in place. I found this...

A 50-tooth spur gear for a Traxxas RC car is available with updated instructions. Version 1.2 features a solid side, while version 1.3 adjusts the holes for improved slipper fitment. The v1.4 upgrade increases bearing hole diameter by 0.5mm, and v1.5...

This is the updated design for the 1/10 scale 4x4 Traxxas Slash's A-Arm. It features standard mounting holes in the front for shock installation, as well as additional holes at the rear to accommodate a secondary shock mounted using my printable...

Traxxas extra rx case - Still Waterproof - Need 3x M3x35mm screew - Highly detailed - All parts are separate objects - Fully ready to 3D Printing - Clean and non-overlapping topology - Model is settled to 0,0,0 XYZ Axis - Make the right size for you...

Fuel Tank Accessory: Precision-Molded Funnel for Nitro Fuel Filling in Traxxas R/C Cars. Enhanced Version Based on Thingiverse Model #45758 Created Utilizing the Customizer App Available at Thingiverse - Customize with Ease! ... Instructions:...

EDITED VERSION, FRESH DESIGNS INCLUDED Updated designs come with a reinforced bumper arm now available in 1/10 scale traxxas slash format. Two strategically positioned holes run through the center of this robust part allowing for an extra stabilizing...