transformers studio series upgrade kit 3d models

I have also fixed the issue with the STEP file which would cause an error message when importing into Bambu Studio. Update 4th November v1.2I have added v1.2 which has an ID of 2.8mm for the AMS and external spool entries and an ID of 2.45mm for...

Here is the OnShape CAD file: https://cad.onshape.com/documents/cb052133db7924fde58ad412/w/585d470d4f1ae3a4aa7b4591/e/4b52144fad6a23b9d824eaa9 Nearly everything is parameterized in the "globals" feature studio tab, so it's trivial to change the...

Cut the slot after these first three parts are glued up.Finally the LED strip is glued to the inside of the black cylinder with the cable routed out through the slot.Here is the OnShape CAD file:...

Credit must also go to the Prop Department and it's various prop vendors on Star Trek: The Next Generation, of whom a variety were involved in replicating these badges over it's 7 year run.These vendors included Steve Horsch and Michael Moore of HMS...

       Done!                              I’ve already planned future upgrades and accessories for this project! They include: Corner mount for Wyze Cam V3Hanging tool storage UPDATES: Added top panel support brackets.  I started using the top as...

Looking to upgrade your Steiner3D revolver? Look no further than the Steiner3D Revolver Mods. With a 1/2 inch threaded barrel and tactical picatinny rails, you can easily attach suppressors, sights, bayonets, and more. Get ready to take your gun to...

It was designed in such a way that creativity for extensions and backwards compatible upgrades are have no limits. Because each part is freely available, it is possible for everyone to implement their own ideas and to share them again. You can copy...

I designed the 'Triaxial Quartz Movement Upgrade', which replaces the clock face in this remix, so it could be used to display the correct time when it was hanging on a wall.The weight in this remix is painful to wind, so make it easier to animate I...

After testing both rudder sleeves, I don't think an upgraded rudder can fully cure the performance issue. It is the design of the boat needs to change to match the longer rudder! :) A simple rudder sleeve to help folks at the club level keep control...

This is a remix of the Prusa MINI Y Axis Linear Rails Mod by Ryper3D that I re-created from scratch from the original Prusa MINI Printable Parts with the following differences:No Ryper3D logo. This was the main motivation for remixing the...

Simple and advanced configuration assistant in 7 sections for "stock" or upgraded printer with: - TMC 2208 or 2209 drivers and LV8729 - SKR 1.3, 1.4, 1.4 Turbo, MKS SGEN L v1 and v2 motherboard - Extruder BMG, Hemera and Matrix Taking in exchange...

Я также сделала два вида крышек, которые позволяют перевозить органайзеры и защищают содержимое от пыли.Parts links below: Handy dispenser 200ml Automatic Toothpaste Dispenser Bathroom Accessories Toothpaste Dispenser Multi-functional Creative...

UPDATE (3 March 2024)I have now finished evaluating and upgrading this model.This model should now be at least as playable as is the original TABLE FOOTBALL GAME. I had a lot of fun re-engineering the original, to: use filament “pins” in lieu of...

This is a Hemera upgrade set of parts for an ender 3 X carriage with a cable chain mount.It is designed around my Anycubic Chiron where the X Carriage was not made correctly and therefore could not be tightened onto the extrusion. This lead me to...

So decided to make my own with a bunch of other updates and upgrades. Slowly but surely, it resulted in a design that looks similar on the outside, but completely new design on the inside. First word of caution. Building this case will be more...

The trigger pull is fairly short at 13mm.Accepts 33 to 38mm OD flywheels (all 2mm shaft fit, superstock upgrade flywheels).Utilizes a horizontal flywheel cage that bolts directly onto the magwell. This is a mounting pattern less prone to misalignment...

I'm uploading the .3mf file for my holder, though this would be a fantastic component for someone to remix/upgrade. The current design works well, though it's a lot bigger than it needs to be and the hexagons aren't particularly strong and can break...

It's a minor issue, but I'd recommend upgrading to a newer version anyways if you're still running Cura 3.6. ###Installation Instructions Install Cura and launch it. Cura will prompt you to add a printer. Pick any one, the default Ultimaker S5...

if not continue here.put the top layer onto the spool side.Step 9:Take the top and screw into the thread in the middle of the tower. You did it, you made your first sorting tower!!!Earlier Versionsif you already have a sorting tower and you wish...

(This step can be hard, i will try to get rid of the crimp with some special junction link in the next upgrade) Gear and drive pod assembly:To avoid the hub comming loose, I oversized an tapped the set screw hole to m4 and I used m4 flat tip...

I have been testing various printed bearings over the course of the last year and am finally ready to release what I am quite confident as the best Y axis bearing upgrade you can perform on your MK2, MK2S, or (most likely) MK3.Video of them in...

... code for making LED panels, but WLED looks like a much better way to go at this point, than using Blynk, and has many more features. WLED is here (https://github.com/atuline/WLED/). I'm planning to upgrade mine to WLED when I get some time. ...

Inspired by the sand drawing tables and the beautiful project SAND watch by Studio AYASKAN, I decided to build my own sand-based clock with a little ancient theme.The sand becomes the watchface as the two marbles draw the time as a line in the...

This is probably the easiest to build version of the series to far. Printing is easy, assembly is even more easy than with prior versions and the transparent ring transmits the light around the entire ring and not only to the inside or outside. This...

Thus, three mini-trays lined up have the same width/length dimensions as one JEDEC tray (the mini-tray is 0.85 mm thinner than a JEDEC tray).The design of the mini-tray aims at small-scale production and storage of small series of components. Small...

It seems to be “the golden mean” between all the other robots represented in the Titanfall video game series. The Atlas’ impressive mobility and imposing armour make it more dexterous than the Ogre and more shockproof than the Stryder. The Atlas is...

I recommend these easy to use soldered connectors (only need a heat gun) to ensure a strong long lasting connection. https://www.amazon.com/gp/product/B083LZS69N Be sure to use the same size and type of wire for each hotend component powered via the...

Added some screencaps as they may come in handy if anyone ever builds on :) added electronics to trigger the plasma cutter, I used a TLP222G-2 opto mosfet with a series 2.2k resistor and 3mm LED, attached it to the heatbed mosfet output (D10) on the...

Identify the point where this line intersects with the vertical center line.Make another reference line 4.13cm up from the bottom of the box.Make vertical reference line 0.7cm from the right side of the constraint box (the line should be between the...

The design of the mini-tray aims at small-scale production and storage of small series of components. Small pick-&-place have limited space for trays, sometimes only a single one. Mini-trays then allow for three times as many different...