transformers g1 hook 3d models

I utilize these two units together to provide 2m and 70cm access from my home shack. After getting these two home and hooked up, I realized how closely they are sized to one another and conceived of creating a complementary enclosure/stand system for...

There are also useful coat hangers and finger toys.Or just check out all my creations.Print instructionsYou can print it without any support, as long as you leave the cut-angle below 90 degrees.Standard settings will be fine, like infill of 20%,...

I made shelfs, tape measure holder, USB adapter holder, cable holder, pen holder, screwdriver holder and some hooks! They're all very easy to print and strong at the same time!  For the shelf itself you can choose a material, I chose...

If you go with the bungee cord I would suggest bending the hooks back to the body so you don't get caught on them. The trigger and trigger lock are held in place with a 20mm and 25mm long M3 bolt respectively. I uses rainbow loom elastics...

If you have difficulties mating the parts, you can carefully use a hammer and alternatingly hammer on both sides with reasonable force. Update: To prevent the modular rack from tilting when weight is added further arway from the board, I added...

At first I thought to hook up a cheap Chinese stereo with bluetooth, but a friend begged me to buy it for the boat. From a client I had a bluetooth module, which was intended for installation in a music center, but it did not fit because the client...

FIRST ASK ME !!\r\n\r\n30.03.2019 Update\r\nAfter printing this part, I noticed that on one side the servo mount doesn't have much space, so I made a hole slightly longer.\r\nI also shortened the names to make it easier to read :)\r\n\r\nThis part...

At 14 years old in 9th grade, I've just started exploring the world of 3D designing and printing, but I'm already hooked. Over the past 15 days, I've learned everything from scratch, teaching myself how to use the software and designing this epic...

IRF520 Schematic: http://robojax.com/learn/arduino/robojax-IRF520-MOSFET_schematic.jpg * Arduino Nano and 2x A4988 drivers * Solenoid: https://www.aliexpress.com/item/32974509060.html?spm=a2g0s.9042311.0.0.27424c4dV2xmWS * Min 12Pcs MR126ZZ (for...

The outer bearing retainer features an interference fit design to provide stability, though it can be secured with adhesive in extreme cases.\nThe crane arm's assembly begins with attaching front wheel braces to smaller main uprights, using angle...

... <font size="+1">^Like</font> button** and turn that heart red <img src="https://cdn.thingiverse.com/site/assets/like-button-liked.svg">.                                                          

Parts Required: Front Laptop Mounts (2 required) Rear Left and Rear Right Laptop Mounts (1 of each) End Spacers (2 required) - These go on the TOP of the bar that runs between the legs (front to back) End Caps (4 required) - These go on top of the...

If you wanted, it would be relatively simple to add a hook and make this a keychain, please let me know in the comments if you want this, or post a remix if you do it yourself. To Print: You will need to print: 2x Straight feet (Green) 2x Tilted...

... mainly with 0.4mm nozzle and with Devil Design PETG. The hoses and the bolts for the hook I printed with a 0.2mm nozzle.

Depending on the type of lights they can produce enough heat to melt them.) Version 4’s hooks were slimmed down in order to allow them to pass through standard grommets that are used on things like flags and banners. (Wind may become an issue. I do...

... </a>and <a href="https://www.prusaprinters.org/prints/33274-customizable-santa-claus">santas</a>. There are also useful coat hangers and finger toys.Or just check out all my creations.Have fun!

You can also get rid of the hole for a hook by setting the HookHoleSize to 0. There's a groove on the underside of the cap for the tube to slide into. This can make it difficult to remove, which might be a solution or a problem depending what you...

I used an OMRON SS-5GL2T (https://www.amazon.com/ELECTRONIC-COMPONENTS-SS-5GL2T-MICROSWITCH-ROLLER/dp/B011N9VGV8) - Two pieces of 1.75mm filament cut to approximately 20mm - Two-conductor cable - Heatshrink - A female jumper or some other connector...

&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;...

... to their placement, also some connectors are polarized. Wiring for 3-pin limit switches includes a 100 ohm resistor in design specifications to avoid damage from incorrect hooking up during testing. ... Well thought-out feedback is much appreciated.

... <font size="+1">^Like</font> button** and turn that heart red <img src="https://cdn.thingiverse.com/site/assets/like-button-liked.svg">.                                                          

Each segment is the same and if you can mix and match with the endcap (another M20 fixing, 10mm threaded hole for fixing hook for hanging, or no-hole). So this could make up 52 holes in total. Printing threaded holes can be difficult to get right,...

Attach some wires to the motor and a 100uF ceramic capacitor between the leads, then hook it up to your motor driver and you're ready to go.\nHow I Designed This\nI based my design on Emmetts geared bearing, which can be found at Thingiverse.com. I...

Two small tabs at the end of the pegs should hook onto the circular bottom lip of the core. Weight disks have two pairs of tabs on the inside, with each tab of each pair being separated by a small, rounded notch. This notch should line up with...

Edit 11/11/2019 - added a new version of the flat top shell with posts aligned tighter and slightly larger hex holes (2.1mm instead of 2mm) but still feels very solid, may need to file about .05mm-.1mm off the hook parts so they fit really nicely,...

The reversible horizontal or vertical manifolds and some connectors allowed me to hook up to rigid 4" dryer ducting easily. Either manifold will fit into the back of the laser in the factory slots, and can be used in either up/down or right/left...

My miter saw has a 5% reverse hook thin kerf blade and cut the phenolic accurately without any burn or kickback. The only challenging aspect might be creating the circular pockets for the magnets if you don't have access to a CNC machine, as it...

Some non-3d printed parts are required but they should be easy to get from your local Bunnings (or similar hardware store): - 2x M5 x 10mm Socket Head Cap Screw, [from...

Once assembled, attach the mount to the light table, allowing the hooks to be pulled away from the surface to accommodate the transparency frame underneath. This setup will hold the frame firmly in place against the light table. Edit: I have...

The above picture is the left handed way (as I am left handed) The spine of the knife faces hook end of the sheath; and the edge faces the outside of the curve of the sheath when sheathing the knife. Some sanding and clean up work may be required...