transformers combiner wars hands and feet 3d models

I extended the length of the center shaft post of the model (Mr. ...Potato Head Feet with Crocs by genevieveccio) so that the feet can be used with a 1990's era Potato Head that my niece plays with.

https://www.thingiverse.com/thing:4636707 was designed to use 20mm springs, so I expanded the feet to fit 25mm ones. Just print 4 of each file. ... Silicone feet not required, but nice to have!

Remix of Steel Sheet holder from daulkarian.I extended the feet to reduced the tendency to fall over

Wanted to change the colour of my DC5 Feet so made my own version on fustion 360.

I designed some feet with a led strip holder. 3 pieces required. ... infill 20% layer height 0.16

Remix of Steel Sheet holder from daulkarian.I extended the feet to reduced the tendency to fall over

To facilitate smoother printing, I streamlined certain details without affecting other vital areas such as the central foot, legs, or upper sections, thus reducing the total parts to four: two modified feet, a revised body, and the unchanged center...

Layer Height: My model is printed at 0.3mm Supports: Yes, manual supports under duck and handle as per photo. Make sure your slicer doesnt automatically put them inside the ducks tube or no water will come out! Please increase your wall...

These files are just the feet and rear PSU Mount for the original Ender 3 psu, When I pick up a Meanwell PSU I will make a file for that as well unless someone else does a remix with one. Remixes are welcome, enjoy! I added a switch panel plate...

Inspired by the spool holder of the Prusa Mini I designed feet and rails to clamp the two bearing-spool holders together. Maybe something similar already exists, but today I was out of luck finding any. Therefore I invested a bit of time to...

This is my design of mounting feet and height extender for the Sculpfun S9. I'm not sure, but I think it should work with the S6 (Pro) as well. These are mounting feet including the possibility to increase the printer, depending on how high it...

Some folks have seen better results with hard feet, helping reduce the prominence of ringing and vertical banding. I had good luck with the old MK2 feet that used felt since I use a paver stone as a base. So I made these to twist into the MK3...

The feet would break during removal from the build plate and the neck would fail during printing as it had to start on support.I've added a patch underneath each row of feet. Now you can carefully remove them from the buildplate with a scraper...

Many CNC frames employ identical feet, so they should fit other setups just as well. EDIT: I've added an extension for these feet now. Simply place it over the existing feet to increase the overall height of your laser. This extension adds about...

These are my adjustable feet and braces for upgrading my FLSUN i3 clone. Its frame is made out of 2020 profiles and these are stiffening the construction in all corners. Print for strength as desired, mine are 3 perimeters and 30 % infill, which is...

Eachine QX90 Lipo holder, protector, and feet upgraded with top-notch components. ...New parts include: Camera: All-in-one VTX and cam TX03 - Check out this game-changing camera setup at https://goo.gl/TNRWXx Motors: Chaoli 1S or 2S Motors - Get...

I modified the feet from here https://www.thingiverse.com/thing:2452078 and used the brackets from another ender 5 electronics box relocation. This design allows you to move the electronics box under the printer and flush to the front so it has...

The LED-equipped motor protection comes in two types, one for the right side and one for the left that needs to be mirrored in your slicer software. The black soft knobs can be purchased from Banggood's Eachine Falcon 210-250 Pro Damping Landing...

... in mind. ...(0.38g) Also includes a version that has feet to keep the frame off the ground when landing. (0.53g) AOS 3.5 / AOS35 / AOS 35 / AOS3.5 arm guards / landing legs / arm protector TPU 0.2 layers, minimal supports if printing with landing feet

This is my design of mounting feet and height extender for the Sculpfun S9. I'm not sure, but I think it should work with the S6 (Pro) as well. These are mounting feet including the possibility to increase the printer, depending on how high it needs...

... so you can put a bolt through both parts into the power supply or just use either part separately. The feet are designed to be printed with the chamfered hole facing vertical, like you would put a screw straight down it and have it fit flush. ...

Designed on Tinkercad, this model was printed in PLA using a CR-10 printer with precise 0.1 mm layer heights and robust 25% infill, along with four walls for added support. Further reinforcement could be achieved by adding additional walls to the arm...

Snap-on anti-vibration feet designed specifically for the Prusa i3 MK3 printer, which effectively absorbs vibrations transmitted through a surface such as a table that supports the printer, resulting in reduced noise levels.

Individual Milwaukee Packout feet for the old style wet / dry vac this is to help with the scaling issue This is a remix from https://www.thingiverse.com/thing:4628200

Duck watering can! ... Print it by itself or with hoe/rake feet for it to sit on. Designed with kids in mind but fun for adults as well. Can hold 2 cups of water. ... #ANYCUBICGARDEN

Made for use in various applications, i combined it with this thing https://www.thingiverse.com/thing:5369309

PETG and PLA should be fine too, just make sure it suits working temperatures around your printer and it's not a clearly brittle one.I used 0.4 nozzle, 0.2 layer height, 3 perimeters, 6 layers for top and bottom, a brim and supports off the...

***IF YOU KNOW THAT THESE WORK WITH OTHER PRINTERS, PLEASE COMMENT AND I WILL UPDATE THE DESCRIPTION!*** Noise and vibration damper feet for your Prusa that install just like those silly little rubber ones in the kits! These bad-boys will absorb a...

Since this spacer is a full 300 mm long, if your printer bed isn't at least 300 mm long you may need to print the smaller half-size pieces and connect them with M3 screws and nuts. There are holes provided for this purpose. There are an...

I love my Furinno "Turn-N-Tube" corner shelves from Amazon for my college dorm/apartment, they come together/apart SUPER easy and make moving them a breeze. Unfortunately, they do not sell extra feet for their shelves as I had hoped. I had 2 of their...