transformers bumblebee 3d model

If you decrease the size of the model, you will end up with less than 2 layers which might decrease the integrity of the maze. You should be OK increasing the size, but the maze walls may not fuse in the middle using 2 layers. You'll need to...

To connect this to the second hand holder disc, I bought a plastic tube of 1mm inner diameter from a modeling shop. I pinched one side a bit to make it flatter. This seems to work, but maybe I will have to glue it on the pin. I didn't do so yet...

Also, no screws or other fixing methods are used. How it works can be seen in the video UPD I added a version in two sides in the form of frames, its printing a third faster and when printing a model, corners closed by cooling by a fan are not...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame that require “supports on build plate only”. I also use 100% infill for all...

I have not modeled any nut traps in the parts because I think they will weaken them so all bolts here just screw into the plastic. I believe the parts are thick enough that the bolts will not loosen but time will tell._ 1. Completely disassemble...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

If you have a tuned in printer, bump the speeds up a little for a dramatic improvement, (make sure wall thickness is a multiplier of your nozzle thickness - The parameters are important and there are a lot of dependencies, Make sure you have done the...

The airflow is higher than stock and the Draken due to its duct design but it has more channels.The main point of developing the Gripen next to the Draken is for printing models that need less but more controlled cooling, meaning it cools from all...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

Based on the given specification for generating an OpenSCAD script that will output a specific shape model made of acrylic plates, here's the script: ```OpenSCAD $fa=5; $fs=0.5; color("gray"){ translate([4,16,-24]){ mirror([1,0,0]) mirror([0,0,1])...

If you want it without internal battery, I have designed this same model without the hole for the battery, remaining in measurements of 126x51x35mm, you have it here: https://www.thingiverse.com/thing:6016310 Required Components: - 1u Mini ZVS...

  ENGLISH-------------Only tested on T12-X, but can work on equivalent models with boxes of the same dimensionsI found my T12-X soldering station a little too bulky, the screen not very visible and too dark. I also wanted to have all the...

Moreover….Sitag astonished me a lot because actually….they continue to make and sell the same model: the famous “Sitag Reality”…which costs now around 700€ !!!Therefore, I decided to try a repair with my engineering skills and a big dose of...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

 You may have to insert a custom hole for a usb lead depending on your mounting position, this could be done in the model, or via a drill after printing.You will need to do some tweaking to keep the led matrix against the grid.  This can be...

Update 2021/02/06: Upgraded parts- steering arm 2.0 Bump steer reduce for steering knuckle 2.0(the ackermann angle have been reduce on steering knuckle 2.0 and therefore with the change of geometry this part is required to reduce bump steer) Update...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

You can use other sized bolts (M3 or M4) files are uploaded for adjustments, I can and will upload different sized models.* *OPTIONAL PARTS* 3x WASHERS (desired size) 3x Nyloc Nuts (desired size) #HOW TO PRINT During the design process I accidently...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

I added some build notes below and a BOM which doesn't include screws, wires, connectors, etc., but has all major components. I planned to revisit this model and release a better version. However I have at least a year's worth of projects in...

This is a servo hinge setup for use with MIPRESIDENT's Iron Man Mark III helmet (http://www.thingiverse.com/thing:260152). You can see my final build here: http://www.thingiverse.com/make:286759 And a video of it in use here:...

The STEP file is included for easy remixing. Please post any makes and if you see a problem please post a comment. Updates: 4-30-2020: Thanks to feedback, I corrected the model for the base, the updated version is "6I". ...None of the other parts...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

Another thing to note is that there have been a few minor changes to the model since I printed the one in the pic, however I don't think anything changed will cause a problem. The STP file is included for remixing. Just wanted to mention some info...

If you don't want to mess with a PLA support, you could probably print this part in two separate objects.I provide you the Fusion 360 file, so you can customize and change the model according to your rail system. I strongly recommend you to...

(see below) That's it, as long as you keep to the above design specs, you should be able to mount almost everything to the base.Cradles are currently available for the following phones:Google Pixel 3AApple iPhone XApple iPhone 11Apple iPhone 11...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

They should easily fit even on small printers; if you can print Hadley, you can print this mount.The mount uses a vinyl disk that sits on top of teflon pads, for very smooth motion.It is very lightweight, and can easily disassembled for compact...

The COMPLETE Order of the Labyrinth bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The strong Minocs of the Order of the Labyrinth are the descendants of Tesevros the Wise,...

Theoretically, it can run more than 11 hours on 1 load (not tested). What parts do you need?Plastic parts:You can use the print files if you have an MK3S or you can use the model files and set everything up yourself. The photos show the position...