trajectory science olympiad 3d models

Trajectory Device Components (Science Olympiad)

These are parts to create my design from Science Olympiad's Scrambler event. Watch the following video for an explanation of the build and how to build it. ... https://youtu.be/qeozLgOoP4Q

Gravity Vehicle Components (Science Olympiad)

Here is the information about a straightforward wing rib created for the 2014 Science Olympiad competition known as Wright Stuff: The rib measures 66 millimeters in length and is precisely 1.5 millimeters in thickness.

This is a simple wing rib for the 2014 Science Olympiad event, Wright Stuff. The length of the rib is 66 mm and it is 1.5 mm thick. Category: Engineering

Here is an egg backstop designed for use at Science Olympiad events with Scramblers during 2015 competitions, adhering strictly to division C rules; make sure measurements align with specifications before implementing this setup. Optimal attachment...

This a Egg Backstop (aka the egg block) for the 2015 division C Science Olympiad, Scrambler. ...It should be fully rules complaint but check dimensions before using this design.</p> <p>Best way to attach it is glue.</p> <p>Note: At time of upload, the...

This is a proof of concept for a geared braking system on the 'gravity vehicle' for 2013 division C Science Olympiad Competition. ...This is / can be made fully rules compliant, with the 2013 rules, with very little modification.</p> <p>Note: This...

This is a prototype demonstration of an innovative braking system designed for the gravity vehicle at the 2013 Science Olympiad Competition in Division C. The system can be fully adapted to conform with the official rules with only minimal...

Mission Possible (Science Olympiad) All Files

Gages are specifically designed to verify roller coaster devices at Science Olympiad tournaments according to the 2019 regulations.

... ...Designed for lifting Science Olympiad hovercraft using an RC car brushed motor in 2018 competitions, it has yet to be thoroughly tested. ...Two distinct fan housing units are included, each featuring different discharge areas and cutoff points.

A Customizable Rib for the Science Olympiad Event Wright Stuff. If You Plan to Utilize This for Your Competition, Please Leave a Comment Describing How It Functions or Any Alterations Made. ... Print Settings: Printer Brand: Printrbot Printer: Simple...

Both the RoadRunner and Tomahawk were Electric Vehicles built for the 2016 division C Science Olympiad. The purpose of the RoadRunner is to create a much faster version of the Tomahawk that can reuse all the parts form the Tomahawk (a few additional...

This sleek and speedy Electric Vehicle is engineered to dominate the 2016 division C Science Olympiad with ease. Built with speed and simplicity in mind, it's a must-have for any team looking to take their competition game to the next level. Before...

Designed in TinkerCAD for Science Olympiad Flight event rubber band airplanes. Printing them all together is fine. One common 608 bearing (ID 8mm X OD 22mm X W 7mm) is used as the weight. Two pieces of 6 or 7mm thick packing foam act as the...

The Science Olympiad Rules for the 2018 season specify a "Circular ring gauge with an inside diameter of 8.0-8.1 cm, weighing no more than 10 g, that maintains its shape and flatness when handled." Version 1: Made in OpenSCAD, this design has been...

To speed checking planes when I'm a Science Olympiad Supervisor, I always make gages. I used to make them from balsa and foam board, but with the 3D revolution, that's crazy. I now model them in 3D to share and print them on my 3D printer for my...

To speed checking planes when I'm a Science Olympiad Supervisor, I always make gages. I used to make them from balsa and foam board, but with the 3D revolution, that's crazy. I now model them in 3D to share and print them on my 3D printer for my...

As a Science Olympiad Supervisor, I make precision gages to speed-check planes. My method has evolved with the 3D revolution - I now design and print them on my 3D printer for instant use. Initially, I crafted gages from balsa wood and foam board,...

When supervising Science Olympiad contestants, I speed-check planes by making precision gages. These gages used to be crafted from balsa and foam board, but with the advent of 3D printing technology, that approach is now absurd. I currently design...

This is a straightforward Wind Power wind turbine suitable for the 2016 division C Science Olympiad. It meets all competition rules, but make sure to verify dimensions before using this design. The Hub Bub is an uncomplicated hub that allows easy...

This is an Egg Transport Vehicle (ETV) for Scrambler in the 2015 division C Science Olympiad that should be fully compliant with rules but please check dimensions before using this design as it has not been tested and does not guarantee performance.

This is a straight driving ETV (Egg Transport Vehicle) for the 2015 division C Science Olympiad, Scrambler. ...It should be fully rules complaint but check dimensions before using this design.Note: At time of upload, the design has not been tested in...

==================================================================== Info on the Design: Both the Wind Whirl and the Wind Whirl Wind were created to allow for rapid testing of different fin designs for the Wind Power Science Olympiad Competition. I...

Fortunately, this design had the added effect of adding just enough length to the OWI-535 with the OWI-535 Gamma Mods to reach the north pennies in the 2017 Robot Arm event from Science Olympiad. The adapter is designed to fit tightly on the...

==================================================================== Info on the Design: Both the Hub Bub and the Hub Bub Odd were create to allow for rapid testing of different fin designs for the Wind Power Science Olympiad Competition. I have...

Both the RoadRunner and Tomahawk were Electric Vehicles built for the 2016 division C Science Olympiad. The purpose of the RoadRunner is to create a much faster version of the Tomahawk that can reuse all the parts form the Tomahawk (a few additional...

Parts to launch the ETV (Egg Transport Vehicle) for the 2015 division C Science Olympiad, Scrambler. It should be fully rules complaint but check dimensions before using this design.</p> <p>2015/2016 redesign: To make it easier to launch the cart...

This is a very simple Wind Power wind turbine for the 2016 division C Science Olympiad. It should be fully rules complaint but check dimensions before using this design. The Hub Bub is an easy to attach hub that allows 1/8" wooden dowels to be used...