trackir hat clip 3d models

I was frustrated by having to wear a hat indoors (which looked uncool :D) and a headset on top of that, so I created an adjustable version of a headset mount, eliminating the need for a hat altogether. This design was printed using PETG for extra...

I designed this mount to be able to remove the TrackIR while not using it, without damaging the smal mechanism on the TrackIR. I designed it for a Steelseries Arctis Pro wireless Headset, but it should also work on others. Additional materials:...

Remix to make the hat clip apartment friendly, use a command strip.

Had to reverse engineer the clip for a Ford Fiesta hat rack.

... providing +5 volts. In the French translation, one shares their TrackIR design for PC simulation games as well. ...The necessary items are three SFH485p IR LEDs, a 10 ohm resistor, a 250 mA PTC fuse, a USB cable and four cables supplying +5 volts.

This is a remix of fasteddys “hinged privacy shutter for a Logitech C615 webcam” to fit on the TrackIR cam/sensor. I made this, since I never really found out what the TrackIR cam can really see or not. It may not be capable of a full video stream...

This is a remix of fasteddys “hinged privacy shutter for a Logitech C615 webcam” to fit on the TrackIR cam/sensor.I made this, since I never really found out what the TrackIR cam can really see or not. It may not be capable of a full video stream at...

This fan mount aims to cool down a hot TrackIR 4 sensor, which can become unbearable after continuous use. To prevent losing another unit out of warranty, a small laptop fan is attached to the top arm using double-sided tape. If noise is an issue,...

This is the mounting bracket that connects the foot with the TrackIR 4 PRO camera and enables it to spin and turn left-right and up-down. ...The pivots where the small rubber pads are inserted (above) might be a bit too long, but I prefer them to be...

Il s'agit d'un support pour le système TrackIR, à fixer sur un écran. Personnellement j'ai utilisé sur sckotch double face plus un sckotch normal sur la partie support car le poids avec trois bras articulés fait se décoller le double face. ...Pour...

I crafted a solution for the non-pro version of the TrackIR TrackClip to securely attach it directly to my glasses. Since I prefer not wearing caps and opt out of using headphones, I needed an alternative approach. This is what I came up with. ...Make...

The mount fits in the tall wedge shaped groove on the rear leg of the TrackIR. The speed control circuit is a very simple MOSFET design like this one http://www.eleccircuit.com/linear-light-dimmer-by-power-mosfet/. Size and simplicity was more...

This is a quick Tinkered remix of Donald Sayers' Clipie Hat Clip. The clip's tolerances are tighter on the pen and marker. I needed something to securely hold a pen and marker to my hat at work and this works great. ...The pen is a Uniball Signo for...

This is a quick Tinkered remix of Donald Sayers' Clipie Hat Clip. The clip's tolerances are tighter on the pen and marker. I needed something to securely hold a pen and marker to my hat at work and this works great. ...The pen is a Uniball Signo for...

This is a light version of my [DIY Heavy trackir design](https://www.thingiverse.com/thing:5260195). **IMPORTANT NOTE: This model is a mirrored version of the official Track IR 5. ...If you wish to use it with that software (TrackIR5), please print...

I rapidly designed this after I lost my base due to my TrackIR 5 malfunction. It's specifically made to fit on top of a monitor that is roughly 33mm thick. If it doesn't fit, you have the f3d files to edit to your liking! The parts are designed with...

wanted to hat clip to hold the golf ball markers that I already printed so I redid this one in Tinkercad. could have done it without this one but I didn't want to have to figure out the hat dimensions part and it worked perfectly. ... Category: Sport &...

wanted to hat clip to hold the golf ball markers that I already printed so I redid this one in Tinkercad. could have done it without this one but I didn't want to have to figure out the hat dimensions part and it worked perfectly. ... Category: Sport &...

wanted to hat clip to hold the golf ball markers that I already printed so I redid this one in Tinkercad. ...could have done it without this one but I didn't want to have to figure out the hat dimensions part and it worked perfectly.

Settings for Scirocco or golf clip for the hat rack. ... Printer Brand: MakerBot Printer: MakerBot Replicator Rafts: None Required Supports: Not Necessary Resolution: Low-Detail Mode Infill Percentage: Fifteen Percent Filled

The Stock Mount for the TrackIR is not the best and doesnt work well on Monitors that are not Square shaped.i use Myself a Samsung G7 and the included mount just slips around and is overall annoying to place.Introducing this Mount, it uses some...

This clip-on hat fits your standard scale Flexi-Rex. Integrated Brow-Bumps snap into place using the pre-existing eyebrows on your Flexi-Rex. Separate color printing models are included, as well as a single piece model for painting. It's highly...

I am a modified version of the original Firefly Q6 Hat Clip designed by btnewman, with one key change: the bottom attachment that secures to your hat has been tweaked to tilt the camera up 10 degrees. This adjustment ensures that the camera's angle...

To clarify, this design is compatible with TrackIR as well as OpenTrack and similar software. Parts needed: 3 IR LEDs 1 resistor (or combine two in parallel if you cannot find an exact match) 1 PTC fuse with a minimum rating of 300mA (I used 300mA...

... between stuff you can't get your hand in to get it. That's where this nifty hat clip comes in. it holds a regular size round style ballpoint pen to the side of your cap. ... I updated version to the newest with a hook to latch on inside brim of hat.

I quickly crafted a new replacement for the clip that holds the hat shelf in my car since I couldn't purchase one. To make adjustments to the design, I've attached the Fusion 360 file as well. ... To reuse the old thread, carefully remove the worn-out...

For a versatile hat clip like Mobius, specifically designed to fit most baseball caps at an optimal angle. These innovative attachments expertly keep subjects centered within the frame during recording. The mirror positioned precisely for the right...

Replacement clip for hat shelves that clamps onto the original cord. No glue required. Tested for 1 series F20. Requires: - 2x countersunk M3x10 screws - 2x M3 nuts Instructions: 1. Print both parts using UV- and heat- resistent filament...

This is a modification of the original Firefly Q6 Hat Clip by btnewman. It is modified to tilt the camera up 10 degrees via the bottom part that attaches to the hat so that the angle of the camera is angled up higher to be more level for those with a...

So I found the Microphone to Tripod Adapter Plate (1/4-20 Female to 3/8-16 Male) by Extraverse and used the threads to make something that the hat clip could hold onto and sit on the tripod. Extraverse's threads fit perfectly first go. I'm not sure...