track saw parallel guide 3d models

This versatile clamp firmly secures a track saw to a sturdy 20mm bench dog, commonly employed on a precision-engineered MFT-style workbench.

This is a T-track bracket that fits a Kobalt table saw. Could be used to make a miter sled or a better fitting miter gauge. ...

I was fed up with lugging around the saw track individually, so I created this track holder as a solution. It's cleverly integrated into the cardholder on any Systainer and securely holds the track in place. ...Just be aware that the Systainer tends to...

ceiling holder Bosch clamps (FSNKZW ) https://www.boschtools.com/us/en/boschtools-ocs/track-plunge-saw-attachments-fsnkzw-199025-p/ Category: Machine Tools

Waste side jigs for track saws / guide rail saws / plunge saws.These are used when you want/need to have your guide rail on the waste side of the line.  If you put the splinter guard up to the line on your workpiece, your workpiece will end up...

 I was trying to have as little lateral play as possible.I've also included a small test print so you can check the fit before printing the whole rail.Update 7/22/2021I've added a version without the “T” that can be used just as a guide.  I...

I bought the Makita 199232-5 Guide Rail Adapter and a Powertec guide rails. When I put it on my XSH04 Circ Saw, I had to give it a little gap to not cut away too much of the rubber. ...I designed this little spacer to slip on so that its the exact same...

Milwaukee Circular Saw (CCS55) Rail Adaptor:- Created for CCS55, to be used on Matika track saw rails (but should also fit festool and milwaukee tracks).- The design is intended to be used with a 6mm thick base plate, for the saw to rest on. ...The base...

This is an adapter to connect the Makita track saw to a 1-1/4 standard vacuum hose (shop vac or similar). I used "low quality" resolution since it's just a functional part. ... Took about two hours to print.

This is a clamping device specifically designed to securely hold a track saw firmly in place against a standard 20mm bench dog commonly utilized on multi-functional task workbenches of the MFT style.

End Stop Designed for 3/8" T-Track on a miter saw station. Made to streamline repetitive cuts at the same size. ... Link to Track Knob Kit: https://www.amazon.com/gp/product/B0824HPPZV/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 Link to design...

Angle stop for old Metabo track saw. Helps to place the Track in an certain angel. I used it in this (german) video: https://youtu.be/UayE6eUxICY BOM 2x M4x20 countersink screws 1x M4 nut The parts are provided in one part. ...Just split the...

This may well work on other saws which have the follow dimensions for the T-track: Base: 22mm the height of the base: 4mm The thin bit width: 19.2mm height of thin bit: 5mm Printing: Anything you really want, I just did it at 30% infill so it has...

I needed them to fix the track of the Parkside track saw. Makita clamps cost around 20€, so...I designed my own! Works well, but you just need to put a spacer on the bottom part of the clamp. I will create also a specific spacer to fit...

... saw, as well as more robust. I included both versions as stl files, as well as the Blender file I used to create these. Link to the saw: https://wenproducts.com/products/ct1065-10-amp-6-and-a-half-inch-plunge-cut-sidewinder-circular-track-saw

Dust cover plug for the Wen CT1065 track/plunge saw. Intended to close blade change hole, which focuses airflow to cutting area and maximizes dust collection. This cover is snap-fitted, easily removeable, and does not interfere with the plunge. ... ...

This precision slider ensures that the track of your old Metabo saw is perfectly aligned. A clear ridge indicates the precise width of the blade, allowing for accurate cuts. The slide features two slots for scoring the cut with a utility knife,...

This adapter fits the outer diameter of the Makita XPS01PTJ track saw. The inner diameter from the vacuum hose is for a 1 1/4 inch connector. This fits perfectly on my setup with just the right amount of grip. Your mileage may. Purple,...

Track Slider for my table saw for feather boards and other accessories. The slider part is designed to take a M5 countersink bolt, I use 65 mm. ...The knob has provision for a M5 nut which I simply drive in during assembly with a hammer.

I have the 100" Wen Track Saw track and it comes in two pieces. To put these two halves together (when needed) Wen provides you with a 3mm allen wrench to loosen and tighten the metal slide brackets that hold the halves together (front and back). The...

This is a dust cover for the Makita SP6000 corded track saw. It is not my design. Someone saw a picture of it on one of my designs and asked me if I happened to have the file and could re-upload it because Thingiverse seems to have deleted it. I...

I am listing a Table Saw T-Track bar that can accommodate 3/4 by 3/8 track. The setup is designed for use with a #8 screw, which has been counter-sunk into the material. I personally prefer using #8 x 1in screws when building jigs from 3/4 inch...

These are end caps that hold two track saw rails of the same length with the tops facing each other so you can store them more safely. The critical mating ends are protected from damage while still allowing the hanging hole to be used. They will also...

These are end caps that hold two track saw rails of the same length with the tops facing each other so you can store them more safely. The critical mating ends are protected from damage while still allowing the hanging hole to be used. They will also...

A budget-friendly option for DeWalt track saw clamps. The design draws inspiration from the Irwin micro quick-grip. https://www.amazon.com/IRWINQUICK-GRIPOne-Handed-Micro-Clamp-Pack-1964747/dp/B00004SBCO I printed these with 5 walls and 100% infill...

This is a 15 cm slider designed to run freely inside the T-track of an Einhell RT-TS-920 table saw; perfect for creating sleds with ease. Three precision-cut holes at the bottom fit snugly onto M6 hexagon nuts. Print Settings: Printer: Wanhao...

This adapter fits the outer diameter of the Makita XPS01PTJ track saw. The inner diameter from the vacuum hose is for a 1 1/4 inch connector. This fits perfectly on my setup with just the right amount of grip. Your mileage may. ...Purple,...

This should fit most track saw rails. Kreg and Bosch will need some editing to make those rails fit. You can divide the model in two or try to transform only the bottom half where the hook is. NOTE: When the print is finished the knob will be...

... item. ... I did not want my tracks horizontal, I wanted to put them upright, so I built a base that the track can rest in. ... Here is the other track holder by @3DDIY https://www.thingiverse.com/3ddiy/designs https://www.thingiverse.com/thing:4571944

I saw people selling the Arbor Cover and also saw variants of it for other tool brands like Festool and Makita. Thought I'd give it a go to try and design this myself. Fits very snug into the Arbor rectangle for me. ... Print time is about 25mins...