toyota tacoma trophy truck 3d models

This replacement steering wheel emblem is specifically designed for the 3rd generation (2016+) Toyota Tacoma steering wheel, requiring the removal of the OEM chrome emblem to fit seamlessly. The holes at the back are carefully crafted for 1.75...

The iPhone 4/4S dock for a 2009 Toyota Tacoma mounts in place of the passenger airbag switch using an Apple 30-pin to USB cable. Suitable for iPhone 4 or 4s with case, the iPhone 5 version is available here: http://www.thingiverse.com/thing:40254. To...

This iPhone 5 dock fits a 2009 Toyota Tacoma, replacing the passenger airbag switch and utilizing the Apple Lightning connector. Designed for an iPhone 5 with a slim case (similar to Elago S5), there's also an iPhone 4/4S version available. After...

Print out 12 pieces of TPU from your preferred source, then remove one side of side-steps from a Toyota Tacoma, ideally a 2020 model but likely applicable to those as far back as 2012. Next, use a mallet to knock the TPU pieces into the empty M8 bolt...

This is a Dash Cam mount for a 2013 Toyota Tacoma. It mounts a SJ4000 camera (may fit GoPro's) discreetly up behind the rear view mirror. The mount clamps to the rear view mirror post and uses a few 4-40" Screws and Heat-Set inserts for mounting. ...The...

Introducing the 2019 Model Toyota Tacoma with an intricately detailed exterior and simplistic interior. The car features four wheels strategically positioned at each corner. Textures are included, while a separate zip file is also available for your...

On the 1996-2000 Toyota Tacoma, an access panel below the headlight must be removed to remove the headlight housing, as shown in the picture. The small metal rectangular panel is held in position with a sheet metal screw and a plastic retention...

Cup holder divider for second-generation Toyota Tacoma owners. When I purchased mine, it surprisingly didn't come with this crucial feature. Since I didn't have XM Radio, I decided to take matters into my own hands and modify a design from...

Mount for a Tekonsha Prodigy P3 trailer brake controller to fit in a first generation Toyota Tacoma (1996-2004). The fuse panel cover replaces the cover for the fuse panel under the dash with a print-in-place rotating latch. I designed the hoop with...

Do you fill your Tacoma with petrol or Taco Sauce. Well? ...Tell the world!</p>

Hi All, This is an adapter that lets you attach a NATIKA WD-011 camera available on Amazon to the factory backup camera location on a Gen2 Toyota Tacoma 2005-2015. I have a 2008 model that didn't come with the factory backup camera, so I got a Pop &...

This thing is a mounting adapter to mount KC Cyclone V2 LED lights under the hood of 2nd gen Toyota Tacoma. Adapters should be placed on either side of the sloped section of sheet metal along the front edge of the hood. These adapters will aim the...

These Replacement Knobs Fit Perfectly on Your 2016 and Newer Tacoma's Sliding Radio Dials, Replacing Those Slippery Originals with Secure Grip.

Modified to fit 2nd gen tacoma. ...slide in the tab on the right side first to get a firm hold and then use the screw to secure it in place.

A friend of mine has a new Tacoma and asked to collaborate on a design to hold a couple of ammo cans on top of the fenders in the bed of his truck. He wanted a place to store some tools and ratchet straps and this seemed like a pretty elegant...

Mine has the Toyota lock (or is it a McGard??) and I simply could not get the tip of the crank with the lock key into the drive. It turned out that I was missing a part that would guide the tip into the slot. I don't recall what was there before but...

This thing is a pair of adapters to connect your brake power bleeder to the master cylinder of your Tacoma and some other Toyotas. These master cylinders have a press on rubber cap and the universal adapter that comes with the pressure bleeder is a...

This mimics the OEM shift boot retainer on the bottom of a Tacoma shift knob that clips onto the shift boot when tightened. Tolerances are tight, 3D print using a flexible filament with supports, then glue onto the bottom of the new knob using super...

This mimics the OEM shift boot retainer on the bottom of a Tacoma shift knob that clips onto the shift boot when tightened. Tolerances are tight, 3D print using a flexible filament with supports, then glue onto the bottom of the new knob using super...

This mimics the OEM shift boot retainer on the bottom of a Tacoma shift knob that clips onto the shift boot when tightened. Tolerances are tight, 3D print using a flexible filament with supports, then glue onto the bottom of the new knob using super...

The dash clock in most first generation Tacomas is broken by now, and if it's still working it is in an odd location, hard to see behind the steering wheel. Mine was broken so I decided to replace it with a universal 4-hole holder. ...I use it to hold...

Double toggle switch plate perfectly fits the compartment to the immediate left of the driver's control panel. ...Suitable for use with the extra-high Toyota shift buttons.

Tacoma 3Gens don't need a fuel cap storage holder while filling up. I mean, who needs one, right? This quick fix provides an easy solution. Application: 1. Print this out 2. Attach a small piece of double-sided automotive tape to the back 3. Add...

One of the few negatives of first gen Tacomas are their door handles which are known to crack. Some of the non-OEM handles are made out of a materiel that does not hold up in freezing temperatures. After snapping a handle this winter I decide to...

This version is a precise replica of the Tacoma's dimensions, untouched and unaltered for any RC chassis. Many enthusiasts have been eagerly awaiting this release. Additionally, this model features no windows. Specs: Wheelbase: 313mm Width at bottom...

I created this based on the idea I found in the 4Runner and adapted it for use with my 2nd Gen Tacoma (2009). I built using PLA at a 0.2mm layer height, and it looks fantastic. I would recommend four solid top and bottom layers and two to three...

Mounting a colorful TRD emblem on the grill of a 2022 Tacoma is next to impossible using the retainer that came with the product. The badge is too large to fit comfortably inside of a “honeycomb” and would have to be mounted protruding outside of...

One of the few negatives of first gen Tacomas are their door handles which are known to crack. Some of the non-OEM handles are made out of a materiel that does not hold up in freezing temperatures. After snapping a handle this winter I decide to...

These holders attach using the existing trim screws in the tailgate of a 3rd gen Tacoma. The base fits flush when tightened, and the screw head is recessed. I built them for trekking poles with a diameter of 18 mm. There are two versions of clamps,...

I designed this to follow the lines of my 2013 Tacoma dash. It use the RAM mount ¼ ball system, along with my Quadlock case for my iPhone. I printed it out of PETG. You do have to remove the dash to epoxy the support plate behind it. I didn't want...