toyota tacoma 3d model

I'm thrilled to showcase my DIY masterpiece, a remake of Maker_Guy's ingenious Chick-Fil-A Cup Holder, specifically tailored for my trusty Toyota Tacoma and its sleek little rectangle holder. Using TinkerCAD as my design canvas, I tweaked the...

Hi All, This is an adapter that lets you attach a NATIKA WD-011 camera available on Amazon to the factory backup camera location on a Gen2 Toyota Tacoma 2005-2015. I have a 2008 model that didn't come with the factory backup camera, so I got a Pop &...

first generation) Toyota Tacoma. The purpose of relocating the vent is to prevent water ingress into the transmission. It definitely works on a 2001 SR5 MT, other years might have subtle variations so YMMV. Note that you need two such adapters as...

This is a faceplate for the 2020-2022 Toyota Tacoma Radio. This replaces the original screen radio with 2 single din slots. Take the old radio out, install an aftermarket radio or two into this, and place it where the old radio was. I have not...

I designed this thing specifically for use in my 2012 Toyota Tacoma with a Sparco wheel (https://www.sparcousa.com/product/l575), NRG Short Hub (https://www.amazon.com/gp/product/B01LPA7F1U/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1) and Quick...

This is a replacement for the plastic cover located to the right of the hazard light button in a Toyota Tacoma. I designed this to interface with a generic phone holder instead of using the mounting mechanism that came with it. I recommend...

This replacement steering wheel emblem is specifically designed for the 3rd generation (2016+) Toyota Tacoma steering wheel, requiring the removal of the OEM chrome emblem to fit seamlessly. The holes at the back are carefully crafted for 1.75...

This thing is an adapter to enable you to connect up threaded Euro 45mm brake reservoir pressure bleeder cap to your Toyota Tacoma (and perhaps some other models) instead of having to use a mega cumbersome "universal" adapter. Use with a typical...

... knob that clips onto the shift boot when tightened. ...Tolerances are tight, 3D print using a flexible filament with supports, then glue onto the bottom of the new knob using super glue. ...Ensure it is facing the right way when glued onto the knob.

... knob that clips onto the shift boot when tightened. ...Tolerances are tight, 3D print using a flexible filament with supports, then glue onto the bottom of the new knob using super glue. Ensure it is facing the right way when glued onto the knob. ...

... knob that clips onto the shift boot when tightened. ...Tolerances are tight, 3D print using a flexible filament with supports, then glue onto the bottom of the new knob using super glue. ...Ensure it is facing the right way when glued onto the knob.

On the 1996-2000 Toyota Tacoma, an access panel below the headlight must be removed to remove the headlight housing, as shown in the picture. The small metal rectangular panel is held in position with a sheet metal screw and a plastic retention...

The iPhone 4/4S dock for a 2009 Toyota Tacoma mounts in place of the passenger airbag switch using an Apple 30-pin to USB cable. Suitable for iPhone 4 or 4s with case, the iPhone 5 version is available here: http://www.thingiverse.com/thing:40254. To...

This iPhone 5 dock fits a 2009 Toyota Tacoma, replacing the passenger airbag switch and utilizing the Apple Lightning connector. Designed for an iPhone 5 with a slim case (similar to Elago S5), there's also an iPhone 4/4S version available. After...

This is a Dash Cam mount for a 2013 Toyota Tacoma. It mounts a SJ4000 camera (may fit GoPro's) discreetly up behind the rear view mirror. The mount clamps to the rear view mirror post and uses a few 4-40" Screws and Heat-Set inserts for mounting. ...The...

Mount for a Tekonsha Prodigy P3 trailer brake controller to fit in a first generation Toyota Tacoma (1996-2004). The fuse panel cover replaces the cover for the fuse panel under the dash with a print-in-place rotating latch. I designed the hoop with...

Do you fill your Tacoma with petrol or Taco Sauce. Well? ...Tell the world!</p>

This thing is a mounting adapter to mount KC Cyclone V2 LED lights under the hood of 2nd gen Toyota Tacoma. Adapters should be placed on either side of the sloped section of sheet metal along the front edge of the hood. These adapters will aim the...

One of the few negatives of first gen Tacomas are their door handles which are known to crack. Some of the non-OEM handles are made out of a materiel that does not hold up in freezing temperatures. After snapping a handle this winter I decide to...

... and z dimensions, enabling you to customize the model's width without affecting its other measurements. Note that this version lacks mirrors; you can obtain them from the Tacoma I or II models instead. ... We look forward to seeing your creations!

These Replacement Knobs Fit Perfectly on Your 2016 and Newer Tacoma's Sliding Radio Dials, Replacing Those Slippery Originals with Secure Grip.

One of the few negatives of first gen Tacomas are their door handles which are known to crack. Some of the non-OEM handles are made out of a materiel that does not hold up in freezing temperatures. After snapping a handle this winter I decide to...

Modified to fit 2nd gen tacoma. ...slide in the tab on the right side first to get a firm hold and then use the screw to secure it in place.

This thing is a pair of adapters to connect your brake power bleeder to the master cylinder of your Tacoma and some other Toyotas. These master cylinders have a press on rubber cap and the universal adapter that comes with the pressure bleeder is a...

This is the custom-designed plastic retaining bracket for the sleek slim body piece located underneath the headlight of the 1st generation Tacoma trucks.\r\n\r\nWhile not an exact replica, this bracket fits perfectly and securely holds that body...

The dash clock in most first generation Tacomas is broken by now, and if it's still working it is in an odd location, hard to see behind the steering wheel. Mine was broken so I decided to replace it with a universal 4-hole holder. ...I use it to hold...

Double toggle switch plate perfectly fits the compartment to the immediate left of the driver's control panel. ...Suitable for use with the extra-high Toyota shift buttons.

Tacoma 3Gens don't need a fuel cap storage holder while filling up. I mean, who needs one, right? This quick fix provides an easy solution. Application: 1. Print this out 2. Attach a small piece of double-sided automotive tape to the back 3. Add...

When installing an "add a fuse" accessory to the fuse box underneath the steering column of a 3rd gen Tacoma, it becomes impossible to fit the stock fuse cover back on without modification. This fuse box cover is designed to provide added clearance...

I created this based on the idea I found in the 4Runner and adapted it for use with my 2nd Gen Tacoma (2009). I built using PLA at a 0.2mm layer height, and it looks fantastic. I would recommend four solid top and bottom layers and two to three...