toyota mr2 aw11 3d models

The owner of this vehicle is a proud enthusiast who drives a sleek and agile 1985 Toyota MR2 AW11 that proudly showcases its original factory design, including a bold red paint job and distinctive pop-up headlights.

Toyota Mr2 Aw11 Badge that is mounted on the front of the car. Comes in a 1:1 ratio (altough not perfect). P.S it does not come with the 3 mounting clips as its intended for universal usage. ... Have fun :D

I've been working on a new line of upgraded models that I'm really excited about, and I have to say, they're looking better than ever compared to their predecessors. ...I plan to keep pushing forward with these updates for quite some time.

This was designed to go together with my other model for the radio mounting brackets with my radio that I have in my MR2. If you have a different radio and/or use different mounting brackets, then download the model without the radio hole and put...

Simple, quick print that uses the stock hardware from the cassette tape holder / storage bin that is typically between the seats on an AW. ...Has some flex to accommodate varying drink vessel diameter.

I'm working on designing this replacement plate in the center console of the MR2 Mk1 that tends to wear out. I've printed this, but I haven't installed it in my car yet. ...I'm printing this on my Elegoo Mars in black, then hitting the high spots with...

These plates are designed to mount a BOSS 625UAB to the center console radio hole of my 1985 Toyota MR2. My car did not come with any sort of radio in the hole, and there were just a bunch of loose wires and 4 holes that would hold up the mounting...

I was looking for a way to hold my phone securely inside my MR2 so I decided to take matters into my own hands. I utilized the clip designed by bcruton and added a base to it that can friction fit snugly between the radio and shift console of my...

Replacement headlight and wiper knobs I designed for my MR2 - printed them out of black PETG with 0.4mm nozzle and 0.2 layer height. I have been running them for 2 years now without issue except very slight warping due to heat. May need to shim the...

My aw didn't come with the battery hold down and nobody online sells ones that fit the special battery holder thing on this old car, so I modeled it. For screws I used 1x 14" J-bolt and 1x 1/4-3/4 bolt from ace the helpful place (tacoma screw was...

Plug and Play Near same dimensions as the oem part Round shape Just mirror the part in your slicer! ... Helps, when the old clip is broken.

Designed to fit stock rubber gasket and mount points.

Designed to fit Ground Control camber plates. MK1b with 4 top bolts. ...I 3D printed the model to make sure it fit the GC plates.

This is a replacement for the poor design of the factory armrest.

Window bracket to Mount Slider Text Case in Toyota MR2 Aw11 rear Window. ... Two Snapper and one original mounting screw of the interior trim.

This is an emblem I made for the intercooler cover on my AW11 Toyota MR2. ...Heat from the engine has not been an issue because this part of the intercooler cover is sealed from the engine bay and, through the grille, is exposed to outside air.

I crafted a custom keychain featuring the iconic AW11 MR2 logo, which I had previously 3D printed with iron PLA approximately twelve months prior. It has remained securely attached to my keyring during that entire period. ...The design was created using...

My MR2 was missing the sticker on its intercooler, so I designed and printed one. I printed it out of normal PLA because I am not too concerned with engine heat. I consider this part of the intercooler cover to be outside of the engine bay...

This is a precision-engineered ring crafted specifically to bolster the dimmer wheel on an AW11 MR2 headlight switch assembly. Notorious for their tendency to crack, these delicate components are prone to damage over time. ...This ring expertly fits...

If you want to have an unbroken new rear hood holder clip in your favorite color. Here it is! ... Infill should be 30 % Use a material like ABS,PETG or similar Simple change: Take out the old pole remove: heat the old clip, until it gets liquid Glue on...

This is the flippable cupholder for the Toyota MR2 Mark1 Armrest. Diameter to fit Standart 500ml cans and bottles (~66mm] No drilling or glueing needed! You need - 4mm round aluminium profile / rod for the hinge - 2x small Screw (s.th. ...like M3x10)

This is a cover for the seatbelt bolt, where the seatbelt attaches to the B pillar. It has enough clearance for the seatbelt anchor to move freely. ...I attached mine using 3M VHB double sided adhesive tape and it seems to hold well enough.

I believe in trust - we can create a world with less shipping and customs due to 3d printing but we have to trust each other. So please print it only for yourself. Everyone needs his daily bread. Now to the part: More Air into the cooler ? Want to...

Inlet flange for 4AGE Toyota MR2 supercharger

Inlet flange for 4AGE Toyota MR2 supercharger

Clutch Alignment Tool for a 1989 Toyota MR2 AW11. Really just a 21mm cylinder, same diameter for the hole in the Flywheel as the ID of the clutch spline. If it prints undersized, scotch tape is about 0.1mm, works great to size it up. ... I could be...

Coolant Reservoir Cap for 4AGE Toyota MR2 AW11 MK1 non-supercharged. These Caps are hard to find these days. Here you only need your oem tubes and a 2mm rubber plate which you have to cut to a ~40,5mm diameter. I use my one (high temp resin print)...

Hello, This is a mounting bracket for the toyota mr2 mk1 (AW11).

Part; T-top SUNSHADE latch pieces.Application; Toyota MR2, AW11 body style.Versions; two versions1) Individual OEM parts (if some of your original parts are usable)2) Modified, all printed parts (if your latch is gone or totally broken)Notes; ASA...

Mark 1 MR2