touchscreen for raspberry pi 3d models

This is specifically for the CR6-SE using the Raspberry Pi 4B and Miuzei 800x480 HDMI 4" Monitor / Touchscreen.

This is specifically for the CR6-SE using the Raspberry Pi 4B and Miuzei 800x480 HDMI 4" Monitor / Touchscreen.

Rasberry pi 4B Housing for your Creality CR6-SE

And that box around the Pi has a lid with an option accommodation for a 40mm fan. There is also a (pretty much just cosmetic) cover for the back center of the screen (pictured in red in the photos) - which is optional too. It is retained by...

This is a remix from https://www.thingiverse.com/thing:4663911 I attached a Noctua NF-A4x10 5V Premium Quiet Fan to the back but it interfered with the printer frame. This moves the display up by 10mm to avoid the problem. ...

The new design fits securely onto the top cross bar using three millimeter screws and T-nuts. Upon closer inspection, I discovered that the bowden tube and wiring were prone to getting snagged on the original mount. ...To address this issue, I've...

<p>Fits on top cross bar with 3mm screws and t-nuts.</p> <p>I fount that the bowden tube and wiring could get snagged on the mount. ...So V2 has rounded edges and dose not sit flush with bottom of the 20x20 extrusion.</p> <h3>Print Settings</h3>...

Fits on top cross bar with 3mm screws and t-nuts. I fount that the bowden tube and wiring could get snagged on the mount. So V2 has rounded edges and dose not sit flush with bottom of the 20x20 extrusion. ...Print Settings Rafts: Doesn't Matter...

Symplified DF robot 5 inch touchscreen for Raspberry PI.

Symplified DF robot 5 inch touchscreen for Raspberry PI.

Discovered this little gem of a touchscreen for a Raspberry Pi which I'm using for KlipperScreen on my Railcore II 300ZL. When purchasing I noticed there weren't a lot of case designs for this particular screen, something I hope to change with my...

Only use PLA This has been tested on these 2 screens (they are slightly different but still work): https://littlebirdelectronics.com.au/products/raspberry-pi-7-touchscreen-display-official...

Bracket for 5 inch HDMI display with touchscreen for Raspberry pi 3 with octoprint.

Here is my case design for the 7" touchscreen for Raspberry Pi by DFRobot. You can find the touchscreen here: https://bit.ly/2Ven1TB. The case itself is just the part name "back", you can mount it on the stand I designed or use a vesa mount. The...

This is a screen holder for a Adafruit PiTFT - 320x240 2.8" TFT+Touchscreen for Raspberry Pi (https://www.adafruit.com/product/1601). ... It has holes for a wire harness and a push button

Screen dimensions: 194x110x20mm (including standoffs); Viewable screen size: 155x 86mm.Files (STEP)-----------------------------------------------• RPi_Touchscreen_7in : basic touchscreen,• RPi_Touchscreen_7in_Logo : touchscreen with the raspberry pi...

The touchscreen stand from McMatt (https://www.prusaprinters.org/prints/15208-raspberry-pi-touchscreen-stand) is great, but unfortunately only for one orientation of the screen.I have adjusted the support lip of the screen and the mounting points so...

This is a stand to hold a Raspberry Pi 7" touchscreen in a portrait orientation. It holds the screen at a 60 degree angle, and allows access to all connections on the Raspberry Pi if you mount that on the back of the screen. I have seen this...

I printed mine with 20% infill. This is for the 7" touchscreen made by the Raspberry Pi Foundation. https://www.raspberrypi.org/blog/the-eagerly-awaited-raspberry-pi-display/ [UPDATE 2016-03-27] I noticed recently the glass on my touchscreen had slid...

This is a stand to hold a Raspberry Pi 7" touchscreen in landscape orientation. It holds the screen at a 60 degree angle, and allows access to all connections on the Raspberry Pi if you mount that on the back of the screen. I have seen this screen...

You might need to tweak this design or make some adjustments here and there, but it works perfectly for me and provides excellent access to the Raspberry Pi's rear compartment where the camera mount lives. Plus, you can attach a RPi-Camera on top! If...

This project is tailored for the 7-inch touchscreen designed by the Raspberry Pi Foundation. Visit https://www.raspberrypi.org/blog/the-eagerly-awaited-raspberry-pi-display/ to learn more. A few weeks later, I observed that my touchscreen glass had...

Raspberry Pi case for 7" display (FYI, I was later sent the same model screen with slightly larger glass. ...I altered the drawing to account for this and uploaded the "large" sized files.Screws for the bezel are 3mm X 25mm with a lock nut75mm vesa...

Raspberry Pi case for 7" display (FYI, I was later sent the same model screen with slightly larger glass. ...I altered the drawing to account for this and uploaded the "large" sized files.Screws for the bezel are 3mm X 25mm with a lock nut75mm vesa...

I took this case and changed it just enough to get my Pi to fit snugly inside, along with the touchscreen. \nThe picture frame part is all fitted perfectly, plus I made the top of the enclosure a bit taller since it was too low on its own. \nI also...

... specifically to match your display's dimensions. ...This model is tailored for a 7-inch capacitive touchscreen device. ...Two distinct file sets are included: one optimized for compact print beds and another designed for larger print bed capabilities.

Also required are two 18650 li-ion batteries with included RE/Discharge protection circuit module, a barrel jack, a Raspberry Pi 7inch touch screen display from Element14 (Kr), an HDMI to D-SUB converter cable (AliExpress item 32451157972), and the...

I added indents in the feet to accept 1/2" rubber feet I had no need to access the USB port on the screen so I just used the modified freecad drawing for the right leg and did a mirror of it in Cura to make the left leg. ... This is used for a picture...

This kit was designed specifically for screens found here: https://www.amazon.com/gp/product/B075JFHLQD/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1. As a beginner in CAD, my designs are quite basic. Each component is held together by a small...

... octo dash. ...Created to fit the below parts from Adafruit. Raspberry Pi 3 - Model B+ - 1.4GHz Cortex-A53 with 1GB RAM https://www.adafruit.com/product/3775 PiTFT Plus 480x320 3.5" TFT+Touchscreen for Raspberry Pi https://www.adafruit.com/product/2441