totalbiscuit top hat 3d models

this is a housing for mounting a Pi Zero to a DIN top-hat railthe cover is compatible with the Pi Zero case with camera

You can easily attach different mounting cages to this base plate with glue. Update: I uploaded a version that can be click-mounted with my Raspberry Pi holder Raspberry Pi holder. The mounting base can be removed from the top hat rail by inserting a...

This ring is a remix from Mstewmakes' "top hat with goggles" design, available on Thingiverse (https://www.thingiverse.com/thing:1686269). ...I added a band to make it wearable for a geek convention.

This is a gorilla tag 3d model I got for free but put into blender and went ahead and added a top hat, moderator stick and the early access badge (NEW VERSION COMING 11/25/2022)

The clamping device that snaps onto the top of the hat rail grip provides an incredibly secure fit, and a 10mm flat surface at the top makes it easy to attach various mounting blocks using glue. A special update (January 4, 2017) was made in response...

The hat hole is 39mm x 52mm. The pipe portion contains a cone at the top to make it printable without supports. The hat brim does need supports, however. To configure properly, set your "Support Overhand Angle" to 58 degrees. ...Otherwise you'll have an...

The pipe section features a cone at the top, making it easy to print without supports. However, the hat brim does require some support. To get it just right, set your "Support Overhang Angle" to 58 degrees. ...If you don't, you'll end up with an...

The pipe portion contains a cone at the top to make it printable without supports. The hat brim does need supports, however. To configure properly, set your "Support Overhand Angle" to 58 degrees. ...Otherwise you'll have an unnecessary support tower...

Inspiration from: [Santa Hat - Christmas decoration that fits onto the top of a bottle of Bubbly! - by muzz64](https://www.thingiverse.com/thing:547041) But a completely new design as derivatives not allowed. Change hole for bottle to a tapper so...

Just a clamp I designed for two potentiometer I need to put inside a control box. The clamp snaps on Potentiometer so it is not really necessary to put a nut on it for fixing. I used my Top Hat Rail / Cap Rail mount base plate to glue the clamps on....

To hold the clamps firmly, I utilized my top hat rail mounting base: (http://www.thingiverse.com/thing:684759) Additional details about the specific potentiometers these clamps were created for are as follows: * Shaft diameter is 6 mm. * Base...

**Updates:** 03.01.2020 * Added low version for Ice Tower cooler (not yet tested - feedback on fit would be great) 22.12.2019 * Added new low version for 30/40mm fans * Added new medium version for 30/40mm fans * Added new low PoE Hat version for...

TOP FUEL FUEL CARBON INJECTOR HAT 2 FOR MODEL KIT - RC - SLOT - CUSTOM DIECAST About 1/25 (resize to fit your engine) Size: 1- 25,22 x 23,22 x 14,98 mm 2- 25,22 x 23,55 x 18,73 mm 3- 25,22 x 23,55 x 18,73 mm For commercial use of the files, contact...

TOP FUEL FUEL CARBON INJECTOR HAT 3 FOR MODEL KIT - RC - SLOT - CUSTOM DIECAST About 1/25 (resize to fit your engine) Size: 1- 32,60 x 30,01 x 18,89 mm 2- 32,60 x 29,03 x 15,64 mm 3- 32,60 x 27,18 x 13,64 mm For commercial use of the files, contact...

A Top Hat mounts two Nimbles on top of a Dual NF-Hotend. Included is a mount for the Hypercube Evo. It's not a simple print as it needs many supports. But I wanted this shape to give it enough rigidity. Edit 1: After some sleuthing by b1840015, we...

Designed specifically for this 4 channel relay: http://www.ebay.de/itm/221584819206, you can easily integrate it into your control cabinet using my Top Hat Rail / Cap Rail mount base plate (http://www.thingiverse.com/thing:684759). Two versions of...

Simply goes on top of the factory top hats between them and the mount on the frame. Mine are printed from Nylon, although PETG should b acceptable as well. Disclaimer Due to factors beyond my control, I cannot guarantee against...

For easier integration into control cabinets, you can employ my Top Hat Rail / Cap Rail mount base plate, available through this link (http://www.thingiverse.com/thing:684759). The holder is presented in two versions. One boasts a flat base suitable...

This is a bare holder to mount your Raspberry Pi B+/2 on so it stands level on the table even with mounted heatsink on the bottom. You can use my Top Hat Rail / Cap Rail mount base plate to easily mount your Raspberry Pi into your control cabinet....

This is a bare holder to mount a 4 channel relay on so it stands level on the table without the risk of short circuit. You can use my Top Hat Rail / Cap Rail mount base plate to easily mount your relay into your control cabinet. There are two...

You can use my Top Hat Rail / Cap Rail mount base plate to easily mount your Raspberry Pi into your control cabinet. There are two versions of the holder: One with a flat base for simple table stand or for glue to the flat Cap Rail mount base plate ...

The 40mm case lid has been reimaged to relocate the 40mm fan, introducing new support structures and strategically placed slots to accommodate the DSLRKIT Poe hat specifically designed for Raspberry Pi4 implementation.

The design boasts an innovative internal shape that ensures the hat sits stylishly back when perched atop an open bottle. This clever feature is made possible by an angled internal surface that expertly orients the hat in its optimal position. Not...

 I simply moved the camera ribbon cable slot closer to the edge as it has to come up between the fan hat and the edge of the case.  Added a simple grid where the fan sits.  Fits perfect and no issues so far. ... I printed in PETG for durability for my...

... and then back to white at around 73mm. All you need to do now is print this delightful Santa Hat design, carefully remove any supports, and get ready to impress your friends with a fun Christmas decoration that's sure to spread some festive cheer!

 I simply moved the camera ribbon cable slot closer to the edge as it has to come up between the fan hat and the edge of the case.  Added a simple grid where the fan sits.  Fits perfect and no issues so far. ... I printed in PETG for...

Great holiday decoration idea: this festive Santa Hat has been crafted specifically to fit snugly atop a bottle of champagne or wine, adding a touch of cheer during the most wonderful time of the year. Designed to be placed on before opening the...

20210110 Update: Having to print supports for the entire bottom edge of the "head" sucks, and the tolerances for the inside edge of the top are not wide enough to fit around the "guts" without sanding or shaving, so I'm going to make some minor...

Baby food container converts into storage case.

<p>Use at your own risk. ...I printed this in HIPS for its superior temperature-resistance compared to PLA.</p>