toothpaste tube roller 3d models

A versatile tube roller, compatible with standard tube dimensions, boasts a unidirectional gear that prevents tubes (including plastic ones) from slipping out. ...To manufacture this component, you must utilize printable supports and opt for 0.1mm layer...

Usage: Insert the toothpaste tube into the twister rod from the side after consuming at least ten percent of the tube. Then twist the knob in your favorite consistent direction. To remove the empty tube, turn it slightly in the reverse direction to...

Usage: Toothpaste tube should be inserted into the twister rod from the side after at least 10% of the tube is consumed, then twist knob in your favorite direction. Remove empty tube by turning it slightly in reverse to loosen and pull out from the...

Make of Customizable Toothpaste Tube Roller by Nother_nEngineer. ...I did not make any alterations to the file.

<p>Design stolen from Deviator2x. Simple, functional, and small.<em>Thanks!</em></p> <ul> <li>Frame mod: Improved pawl - more flexible and less likely to snap off. Perhaps more likely to break if you try hard to turn it backwards. </li> <li>Key mod:...

Design stolen from Deviator2x. Simple, functional, and small. _Thanks!_ - Frame mod: Improved pawl - more flexible and less likely to snap off. Perhaps more likely to break if you try hard to turn it backwards. - Key mod: The key is 6mm...

Customized version of https://www.thingiverse.com/thing:4200973 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4200973

Customized version of https://www.thingiverse.com/thing:4200973 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4200973

I really liked the original, but after first print, the knob was very tiny, and the shaft of the roller was just short enough, I didn't want to glue the cap on. ... I lengthened the shaft, and made the knob easier to grasp, and now it's perfect for...

I truly appreciated the original design, but after the first print, I found the knob to be extremely small, and the shaft of the roller was just barely long enough - I didn't want to attach the cap in that state. ... I extended the shaft, and made the...

Enhanced grip circumference through enlarged control dial dimensions

Just made a support from scratch for this toothpaste squeezer. I call as remix because idea from https://www.thingiverse.com/thing:44200 I use 2 threaded inserts in the back to better fix in the default hole of the side of the furniture, but with...

Toothpaste tube roller I used PTEG print center laying flat with 5mm brim at .15 layer handle and housing at .20 layer printing housing slow with good adhesion so it doesn't fall over this design has been thoroughly tested comparing favorably to any...

This is just a simple toothpaste tube roller. ...The picture has initials on it but the file doesn't.

This is a straightforward Toothpaste Tube roller that I designed one afternoon when I had some downtime. I created it using Inventor and printed it out with my DaVinci Jr. 1.0. The entire process takes under an hour, and I've been utilizing it for...

The toothpaste tube roller leverages Elian Feenstra's innovative tube model, providing a sleek and efficient design for optimal oral hygiene performance. ...This clever contraption employs Feenstra's principles to roll out a precise amount of toothpaste...

Toothpaste roller

Toothpaste roller, attach this device to the bottom of your toothpaste tube and roll it across the surface to extract every remaining drop of toothpaste.

A toothpaste roller has been designed that prevents the tube from unrolling due to its innovative mechanism. ...It takes approximately ninety minutes for this device to successfully complete its task.

This is a make of Toothpaste Roller by BoomZilla1, Thingiverse 2728757. ...I did not make any changes to the files.&nbsp;So far, I have not been able to get a tube to roll inside the chamber.&nbsp;

Toothpaste rollers are designed with a built-in system that prevents the tube from unrolling. The printing temperature is set at 212 degrees Fahrenheit. The build plate temperature is maintained at a steady 65 degrees Fahrenheit throughout the...

I recently discovered that most of my toothpaste rollers are constructed from plastic. To circumvent this issue, I devised a simple solution involving a miniature lock and hold. By inserting this tiny holder into the plastic-packaged tube, it remains...

This is a make of Thingivserse 1032924 - Toothpaste Roller by Deviator2x. I did not make any alterations. ...This is the first version of the model.

Remixed toothpaste squeezer/roller to improve tolerance/slop. &nbsp;Various versions in the sketchup file, the print in place ones are untested. ...&nbsp;</p><p>Remixed from https://www.thingiverse.com/thing:44200</p>