tmnt 3d

You can cut the circle that's sandwich between the two 3D printed pieces with good scissors. The holes for the crews and the tube are harder to make. Be careful, this mesh is sharp and you can get cut. I'M SERIOUS. I managed to make the screw holes...

Dragon and Mosquito use the same length of PTFE tube which is why they share jig.BOM - Bill of MaterialsI buy most of my 3D printer parts from quality stores on AliExpress. Shipping takes a while from China but quality is excellent and the prices are...

Four screws for every corner and 8 screws for every side.[blue] NO acrylic glass holder at the side where the hinge mechanisms are located!From this on the “Front” is where the hinges are.[green] At the location of the green circle you can drill a...

My bot came with 410 mm Y rods, which is reflected in the Blender file, but this design should work on older printers with shorter rods (the original i3 had 330-335 mm Y rods). The .blend file depends on my standard parts/materials library, which can...

See “Large Binder Clip Tentacle Monster” below in connectors.Tentacle Rail Clip BaseThis Tentacle System base includes a clip that attaches to the T-Slots in the aluminum extrusions used in Prusa and other 3D printers. Used in combination with the...

I did not try to 3d print everything in plastic if metal or wood made more sense and was faster/stronger/easier and not cost prohibitive.  3D Printing is mostly used for the connections and exact positioning of tubing.Everything here is my own design...

If you don't own a 3D printer but have seen this blank somewhere else and want to use it, I recommend just asking in a furry group chat on a platform of your choice. Many furries are also tinkerers and may print this for little money.</p><p>The base...

What to print: Print these files: icarus-1.2.1-for-sherpa-mini-r1-normal.stl sherpa-mini-r1-dragon-mount-1.1.stl icarus-dial-holder-1.0.stl icarus-belt-peg-1.2.stl icarus-fan-duct-1.3.1.stl...

It can hang off the plywood deck (¾ inch") or the slightly thinner shelving above.&nbsp;Support enforcers are neededNo gluingEasy to printDesigned on...

What to print: Print these files: icarus-1.2.1-for-sherpa-mini-r1-normal.stl sherpa-mini-r1-dragon-mount-1.1.stl icarus-dial-holder-1.0.stl icarus-belt-peg-1.2.stl icarus-fan-duct-1.3.1.stl...

Avoid lifting and warped prints!Print all three parts (body, treads, roof option.)Superglue the treads to the body.Choose the roof option and glue, or leave it free and swap it out as needed!Superglue works best for gluing it together.It will scale...

Micro USB Breakout Amplifier 14 x M3.12 Plastite 2 x M4x45 Screws 2 x M4 Nylock Nuts 4 x M3x14 Screws 4 x M3 Nuts Dual USB Panel Mount Single USB Panel Mount 7" Capactive Touch Screen with 1024x600 Pixels or Pi Foundation Screen 800x480px Flat Flex...

It's yours to make!).Stand up your Space Port before it's too late!&nbsp;More Space Port!Space Port - https://www.printables.com/model/205432-space-port-terrain&nbsp;Space Port Living Quarters -...

Worlds are waiting.Equip yourself today, citizen!Space Port - https://www.printables.com/model/205432-space-port-terrain&nbsp;Starship Cargo Pod - https://www.printables.com/model/224797-starship-cargo-pod&nbsp;Starship Transfer Tug -...

Use thread lock to ensure these will not accidentally come loose.A 36mm diameter propeller should run freely inside the rudder at all rudder angles.Mount the rudder support to the hull using M3x6mm screws.Then put another M3x6 screw to secure the...

Remove the stock z-axis tops and replace with this light bar mount.Dual Mount Z-Axis Top No Switch: Same as Dual Mount Z-Axis Top with no hole for the power switch.&nbsp;&nbsp;Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill:...

I'm not telling you how to 3D print parts and clean it. You know it. BOM: '1. RPi 3A+ / Zero W /Zero W2 (and similar clones that have the same outline as Zero), microSD card, '2. Raspberry PICO working as keyboard martix USB HID device...

Clogs are a thing from the past and no more grinded up filament stuck in the gear.Here's a comparison picture by Hercules user techguychad:What to print:Print these...

Operated with a driver or remotely/programmatically with an AI, much of the work performed in the Space Port can be automated.Reducing risk.Eliminating squishy biological beings.Increasing efficiency and profits!Upscale your space port, eliminate...

I think the pipeline will look even better in PLA.Designed on Tinkercad.No supports required.Superglue the valve handles.Also, see:Above Ground Pipeline Addons - https://www.printables.com/model/222945-pipeline-addons&nbsp;Space Port Fuel Station-...

I illuminate my RepRap 3D printer's control panel with it. The LEDs require a 12-volt power supply which can be supplied by the printer electronics (Rumba Board). Material: ABS, 3mm thick Nozzle: arcol.hu hotend v4.1.1, 0.35mm diameter Printer: DIY...

With external markings and without.Stand up your Space Port before it's too late!Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under...

... at 0.2 layer height.</p> <p>But once you've raised the limits, it's worth seeing what a 350mm/s travel move really looks like at 5500 or 6000 mm/s^2. (Answer: sorta scary, honestly) Designed from scratch in SketchUp. Category: 3D Printer Accessories

Remove the z-axis tops and replace with this light bar mount.&nbsp;Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill: 15% GyroidSupports: Build plate onlyOpen 3MF files in PrusaSlicer for preconfigured settingsRequired...

Clogs are a thing from the past and no more grinded up filament stuck in the gear.Here's a comparison picture by Hercules user techguychad:What to print:Print these...

By doing so, I can now get more of the STLs to show up in 3D view on this site. The updated files have 10-18-23 dates and are renamed with "-remake" or "-k". 10-10-23 Update: Two items - Assembly Hints and Images added as a new section, and an...

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ ~...

(That's something else, sorry.)Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

The servo spindle should be towards the middle of the robot.COGCut the servo horn with a pair of wire cutters so that it fits into the cogPush the servo Horn onto the cogMake sure the servo is at the minimum rotation position (turn it clockwise until...

Feel free to rescale as needed.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...