tl smoother ender 5 3d models

This is a remix of Ender 5 casing TL smoothers by D_jespersen I have added a cover to ensure adequate spacing for heat dissipation while preventing any wiring from touching the diodes. ...

When I prepared my Ender 5 for smoother installation, I had to create an adapter to secure the component in place without metal contact inside the power box and board. To accomplish this, I designed and printed these caddies, which proved to be a...

The Ender 5 TL Smoother Mounting Bracket seamlessly integrates three smoothers into a compact design, safeguarding the PCB with reliable electrical insulation and effortlessly positioning them near the original stepper motor connectors.

... smoothers, but XY should suffice. Still, I had them lying around and thought, "Why not?" This custom holder is designed specifically for my Ender 5 TL Smoother, which you can find on Amazon at the following link: https://www.amazon.com/dp/B07QFV9MPG

Case Made For TL-Smoother Board Size: 4.9 * 2.8cm / 1.93 * 1.1in...

Use 8pcs of M3x6 screws and 2pcs of M5 nuts, securely mounting them onto the original frame. ...If you appreciate this design, consider showing your gratitude with a generous tip through PayPal at https://www.paypal.me/Djdenzo.

0.2 layer height supports: yes mounts to back of lcd screen with stock bolts make sure you replace the ground fork

Attach a TL Smoother to your 2040 or 4040 profile with this easy-to-use clip, currently under development. ... Important Note: Trim the pins at the bottom of the PCB if necessary for a secure fit.

There are numerous tl_smoother supports available. Why build another? I wanted something compact, quick to print – it took just 10 minutes for half a sheet – minimalist, and robust enough to stand on its own in an open space. Voilà! ...:)

I only had to operate two TL smoothers, so there was no need to design and fabricate a mount for four; instead, I modified the original creation using Meshmixer. ... Original https://www.thingiverse.com/thing:2993906

Support to hold the TL-Smoother modules involves securing them in place, which is crucial for optimal performance. ... You can find suitable support systems on Aliexpress by searching for "Trianglelab 4-units pack TL-M module addon PLUS smooth motor...

I wanted to preserve the original electronics lid because it's made of metal and features a sticker displaying detailed model information, so I created a TL Smoother mount (for X and Y) that attaches to the inside of the electronics box. To secure...

TL Smoother Holder for ENDER 3 PRO with Trianglelab Smoothers 25x48mm. Inspired by the innovative design of https://www.thingiverse.com/thing:3464858, this TL Smoother Holder is specifically engineered to work seamlessly with Trianglelab Smoothers...

Parts Needed: ================ * 2x M3 6mm screws per Smoother * 4x M3 14-16mm screws * 1x M3 20mm screw I designed this top cover to replace Ender's, providing mounts for up to four TL-Smoother boards from MKS. The smoothers are vented to...

... ___ ## ** Ender_Case_28x45.stl ** TL-smoother details: SIZE: 28X45mm **Notes** This model has not been tested. First, try to print the test model (TEST_HOLDER 48x25.stl) to verify that the module fits. ...Then proceed with the full housing print.

A superior holder for TL-smoothers tailored specifically for the Ender 3 Pro.\r\n\r\nThis innovative design accommodates two TL-smoothers (30x40x1.5mm) for seamless performance on both the X and Y axes, effortlessly fitting into the tight spaces of...

Link de compra:...

Update 20200122: I've managed to make a design which can fit three (3) TL Smoothers into the factory Ender-2 electronic enclosure. It's an <strong>extremely</strong> tight fit, however, so make sure the wires are bent clear and be careful when...

But then, I thought I needed to remix this and make it 4 slots for my Ender 3 Pro since the TL SMOOTHERS come in a pack of 4 from amzn.to/350KH0d. After printing it, the initial remix I did couldn't fit. So tonight, I tried to revise it again and...

Update 20200122: I've created a design that accommodates three (3) TL Smoothers within the factory Ender-2 electronic enclosure, but it's an extremely tight fit so be sure to bend the wires clear and exercise caution when reinstalling the cover, with...

... it easier to install. For a visual guide on how to do this, please check out the movie at this link: https://twitter.com/matakino4989/status/1045295128389140481 This holder is specifically designed for incorporating TL-Smoother PLUS into Ender-3.

This is a custom mount for two triangle labs TL Smoothers Plus inside the motherboard case on the 4040 aluminum extrusion. It will require three hammer nuts and three 3mm screws to install. Please note that this design has not been thoroughly tested...

L-Smoother support for n4 to be inserted into the proper guides. Use the V1 (support feet), or glue the V2 and V4 to the original iron cover near the fan as shown in the picture. ...For other clarifications or ideas, contact me directly.

Attach a sleek new holder to your Ender 3 Pro. ...Simply apply double-sided tape to secure it firmly on the fan side of the electronics enclosure.

... is designed to use no additional screws. ...For assembly, I recommend first placing the support without TL-smoothers on the lid, then carefully putting the TL-smoothers with their already connected cables into their respective guides and you're ready.

The TL-SMOOTHER is a useful tool for decreasing or eliminating the salmon-like appearance that can occur on certain 3D printers. It helps to improve printing quality in open loop stepper motor-based 3D printers, ensuring smoother and more precise...

TL-OptimizerBoosts print quality by eliminating salmon-like effects in select 3D printers. Specifically designed to enhance performance on open-loop stepper motor-based machines. ...Learn more at https://bit.ly/2v0T7V6

This is a Ender 3 Case for TL-Smoother Modules & Leads

This is an Ender 3 case designed specifically to house TL-smoother modules and leads with precision.

I've purchased the AliExpress 30x40 8 diode TL Smoother and required a spot to hold them on my Ender 3. I stumbled upon something on thingverse for other TL Smoothers sizes, and remixed Matakino's TL Smoother holder. You must press in the boards so...