titanic models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

Additional mounting types are avaiable for this model.This explosion proof LED light fixture is paint spray booth listed, IP67 rated, dust-proof, and protected against high pressure jets and temporary submersion. The cast aluminum body and LED lamp...

Please check the pictures to see what's in this kit.This set includes: - Requiem Demon Hunters (6+6)- Requiem Wulfhearts (4+4)- Captain Fenrir - The Silver Hunter- Captain Fenrir - Wulfheart Form- Trisha the Houndmaster (+2 Mastiffs)- The Old Wolf...

Comments and suggestions are also very welcome. ### Update 2020-10-19 Kermi radiator mount clips now available Quite a few new MultiClip Objects in the collection (link above). ### Update 2018-09-21 Updated the alignment helper New: MultiClip...

However, they are split down the middle so they can fit through the holes with a firm hand, before springing back to the larger size. So thank you for the reviewer who made me take a closer look at at my model.I am always open to others ideas or...

Most parts do not need support and can be printed using the model orientation. BaseTopMotor and the Lid need “support on built plate only”. MotorMount needs to be rotated by 90 degree on the closed end (the one with the screw holes). In addition, it...

The original interior geometry from the Prusa filament sensor has been incorporated into this design, sourced from Prusa's models. The pinda is in the same location as on the original. The nozzle in this new design sits 10mm further forward along the...

 A side note - you also probably should be using my rear PC4m10 jack for your MMU3 https://www.printables.com/model/542409-mmu3-pc4m10-rear-connector The perfect length is one make an even curve downward and the up into the back of the MMU that is...

The Jedi who wields it is called “F” in the credits.This is a remix of my older model. The biggest changes are:</p><ul><li>Improved mechanism for opening the emitter. It opens up by pressing the blue switch on the side, just as it does on screen. To...

This set collects a number of fantasy character models and makes them available for use in Pocket-Tactics. This set doesn't represent a specific faction, just a number of loose pieces to use in your own custom builds, either keeping within this...

For the second core set, we've gone with the old "elves versus dwarves" match-up, featuring Max Maurel's fantastic dwarf models (which he originally designed as replacement pieces for the old dwarf set and finally getting their due). Stay tuned for...

I designed this model for my daughter, who wanted a treasure chest to go with her pirate costume.  She wanted it to be “really big”, so this design utilizes the nearly the full volume of the MK3s to make three sections that bolt together.  It has an...

...I propose some activities to do programming this robot: First goal: Making it move The first and basic activity could be to program and model their movement, to find the correct position sequence for each leg for a forward run. First step: assembly.

 A lot of my models are designed for the 2.49mm walls that equate to 6 print lines with a 0.4mm nozzle.  </p><p>Both the Tool Holders and the main Jig are setup to have a color transition at Z height. ... </p><h3>Donations</h3><p>If you found this print...

Comments and suggestions are also very welcome.Update 2020-10-19 Kermi radiator mount clips now availableQuite a few new MultiClip Objects in the collection (link above).Update 2018-09-21 Updated the alignment helperNew: MultiClip Glue!Update...

I would also suggest allow for extra LEDs in your strips and to slide in your LED strips as you combine a segment to other segments. All in all, I learned a great deal about modeling using Fusion 360 and 3D printing using Slic3r and the Original...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

It is essentially based on my first design.If you don't have an AC Infinity T8 or don't want to spent 120 bucks on one just to disassemble it, check out this simpler and cheaper...

 The switch is wired so it goes from Off to On with no sounds to On with sounds. ...

Printing time is &gt;15min.Credits:The original configurable OpenSCAD model is by wstein, posted here. ...Thank you Werner!</p><p>Thanks to <a href="https://www.printables.com/social/78665-darktiger/about">darktiger </a>for his print and picture of the...

If desired you can secure it in place with a sticky pad or some hot glue. Push the insert into place. Lower the NeoPixel Ring into place, ensuring to route the wires through the slots in insert. If you are using a diffuser, place it on top of the...

[This project is still being actively printed, I will update this model with pictures, &amp; upload remixes as I go through the iterative process.Update May 13th 2022: modified shelf hinge diameter to better slide on the poles, added drawing for...

The Raspberry Pi controller has a radio module attached to it for issuing commands, though I used the slightly different NRF24L01+PA+LNA model which offers better range. You could also use the same NRF24L01+ module as the puck uses, the wiring and...

... broken and no one is going to fix it. Download files one at a time by clicking Download each time. ### My some other things: Category: 2D Art

If in doubt refer to Mehdi for more demonstration material.I was basically trying to address two "issues" of my Anycubic Vyper:The PSU and Mainboard 24V fans are very loudI want to upgrade my Vyper with an OctoPrint/OctoPi setupSo here is my...

This model involves many grams of material but also many hours of slicing, printing and overwatching your printer. I suggest you to print the main parts in 0.2mm layers if you don't want it to take forever :S and use something between 0.4 and 0.5 mm...

The assembly is not complicated, for each configuration I put exploded photos, pay attention to the insertion of the brass threads, (there are 2 models you need both), and to the direction of insertion, those placed in the attachment of the guides,...

The bracket that goes around the metal fan cover is specific to the Ender 5 Plus (also used on CR-10, CR-10S, and many of the other Enders) but does not fit all variations (V2, V3, CR-10S Pro models does not fit.) A list of the printers I think this...

As applicable for all home brewed masks with a filtering purpose: this model is not tested by given standards, the functionality is not verified, and it’s not certified in any manner. Be aware of the risks and use it on behalf of your own...

It's worth the trouble to get access to a laser cutter to get cut panels.&nbsp;&nbsp;The duct is intended to print at a 45 degree angle - the part model is oriented as it is intended to be printed. The duct part DOES NOT NEED SUPPORT. Your slicer may...