titan direct drive 3d models

Created for the Hydra fan duct & tool change system: https://www.thingiverse.com/thing:4062242 It has cable management built in that works with my hotend chain: https://www.thingiverse.com/thing:4170246 This is designed to make a cloned titan...

CR10 - TİTAN DİRECT DRİVE

CR10 - TİTAN DİRECT DRİVE

Created to enhance the Hydra fan duct & tool change system: https://www.thingiverse.com/thing:4062242 It features built-in cable management that seamlessly integrates with my hotend chain: https://www.thingiverse.com/thing:4170246 Designed to convert...

A bracket for the TITAN direct drive extruder to have bl touch compatibilities.

Made this because I didn't see any titan direct drive mounts that fit for my Tronxy XY2 Pro that has a titan extruder. ...This only works with a nema 17 pancake motor because the motor will hit the gantry before getting to the x axis stop.

I've been tinkering again and I've come up with the Hero Me e3d Titan Direct Drive with 5015 blower fan, it's not entirely my own creation, rather a fusion of different components cobbled together in Tinkercad. This hybrid build is remarkably...

I needed a part cooling fan as soon as I switched to my Titan Direct Drive, so I built one myself. It also has mounting provisions for DC42's mini IR sensor. This design can be printed without support, except for one bridging section. To ensure...

E3D Titan Direct Drive Mounting Bracket for Smartrapcore Printers This mounting bracket securely fastens to the standard hotend bracket location, utilizing four screws to provide a sturdy attachment point for the E3D Titan. The E3D Titan then holds...

https://a360.co/2I7ViwZ ###Specifications### - Suitable for a frame made of 3030 extrusions - Use 2020 extrusion to mount the rail on the X-axis - MGN12H Sliding rails are used (MGN15H would be a better choice, but it was not designed with this in...

... getting stuck in closed position. Update: June 24nd 2016 @ 6:33pm Dual_Titan_Print_Fan_Shroud_rev6 - Angled nozzles to direct air downward at nozzle tip. ...I widened the nozzles slightly and increased height of nozzles to allow for more airflow.

This is support part for Titan.

This is a mount for the Titan direct mount designed specifically for the Vulcanus style CoreXY printers. Several modifications are required to be made by hand, using a drill bit, to the bottom and middle bearing holders of the XY Carriage in order to...

The community lacks this, so I made my own, been working well for me, if you have just bought a A1.1 titan extruder, you may want to print this if you have Bl Touch or 3D touch, works for both

Up date for direct drive extruder for Tronxy X5SA using titan extruder. this so far has been workibg great. ... hope you all enjoy.

I whipped up a custom mod for myself, figuring I'd share it with others. ...This mod is designed to fit the Petsfang Direct Drive Mount rather than the Titan one, allowing you to utilize your stock extruder seamlessly.

This was a really good model for a direct drive mount for ender 3s, but I have a Tronxy XY2 Pro which isn't the same. ...I decided to remix this design and make it compatible for the Tronxy XY2 Pro with a titan extruder.

... imminent! ...This X carriage fits stock bearings/bushings for E3Dv6 clone and Titan clone in direct drive setups, featuring an arm to accommodate a BLTouch sensor. ...For optimal part cooling, attach fan to the inside of the arms, aligning with hotend.

X Carriage designed for direct drive setup with E3Dv6 clone and Titan clone, utilizing stock bearing/bushings, along with an arm that holds a BLTouch sensor. ...The part cooling fan should be mounted inside the arms for optimal alignment with the...

... Use X carriage for stock bearing/bushings when working with E3Dv6 clone and Titan clone in direct drive setup with arm holding BLTouch sensor. ...Mount part cooling fan on inside of arms rather than outside - it should line up perfectly with hotend.

Attempt at your own peril.\r\nThis project is still evolving, I'm about to initiate test prints shortly.\r\nX Carriage designed for use with standard bearing/bushings compatible with E3Dv6 clone and Titan clone in a direct drive configuration...

X Carriage designed for use with stock bearing/bushings, compatible with E3Dv6 clone and Titan clone in direct drive setup, featuring an arm that holds a BLTouch sensor. ...Part cooling fan should be mounted inside the arms, not on the outside, aligning...

I wanted to go direct drive and get rid of the bowden tube, but the original print was not a fit for my actuators. This remix can handle allmost any size actuator motor size, and as an added bonus there is a mount for the Filament out detector. ...

Direct drive allows for many advantages, including reduced retraction and better compatibility with features like "Linear Advance" and "Pressure Advance". I bought a cheap Titan extruder clone to give it a try, thanks to its geared reduction, a...

This uses an: • E3D hotend (1.75 direct drive or universal). • The Titan extruder • A pancake stepper motor (https://www.omc-stepperonline.com/nema-17-stepper-motor/nema-17-bipolar-1-8deg-13ncm-18-4oz-in-0-7a-2-9v-42x42x25mm-4-wires.html) • 3 x m3...

This Mod was designed with the intent to use as much stock parts as possible of the 2022 tronxy x5sa pro 400 and make it direct drive (without firmware mods) !!! ...apart from a 5015 blower if you want (will add a smaller 4010 version if requested) ...

This Mod was designed with the intent to use as much stock parts as possible of the 2022 tronxy x5sa pro 400 and make it direct drive (without firmware mods) !!! ...apart from a 5015 blower if you want (will add a smaller 4010 version if requested) ...

I liked this mount for my stock extruder as it was really solid so made one for the titan, so its now mirrored to have the Titan on the left and the stepper on the right and holes adjusted. I run this with a Hero Me setup but my mod of the Gantry...

It securely holds the genuine E3D Titan Extruder, equipped with a pancake stepper motor. ...Additionally, I made some adjustments to the popular 5015 fan shroud duct to ensure it fits perfectly: https://www.thingiverse.com/thing:2175956 9/8/2018 - I...

That's why the Titan Extruder caught my attention - it's a lightweight option that fits seamlessly into my setup. After some tinkering, I was able to mount it without any issues during testing. ...Printing TPU at 30mm/s has been working smoothly, and...