tinyhawk 2 insta360 go 3d models

Just a very basic insta360 handle, couldn't find one so I remixed the https://www.thingiverse.com/thing:2686278 in prusaslicer To improve strength of the screw, just print it horizontally with supports. ...

Here I made an Insta360 Remot holder for the Extension Stick. The holder clamps over the tube and can also be secured with two rubber O-rings. ... Have fun with it.

Hotshoe mount for Saramonic Blink500 receiver on Insta360 One R. The receiver will be invisible in the 360 stitch. ...The rod on the mount is to securely wrap the audio cable so that the cable is out of sight.

This allows an Insta360 OneR to be mounted on a GoPro base. ...The OneR must be powered by the drone battery using a voltage regulator and a USB C plug.

Insta360 ONE RS 1-Inch Holder/Holster You can carry the camera with the invisible stick and lens cover attached. And You can also hang it on the wall. ... Please remove the supports after printing.

Insta360 Remote Mount for a GoPro Adapter I used 2x M4x12 DIN7991 to fix the two parts together. ...Additional to that, I weldet the parts with my soldering iron together.

Insta360 One R Battery Terminal Cover I made this out of TPU to protect the contact terminals from getting dirt in them. ... I recommend you use TPU flexible filament only

Insta360 ONE RS 1-Inch Holder/Holster You can carry the camera with the invisible stick and lens cover attached. And You can also hang it on the wall. ... Please remove the supports after printing.

I wasn't happy with the GoPro style holders for the Insta360 Go2, so I mixed together the official GoPro mount with one I was already using for the 2Fiddy.

Several parts for the FlyWoo Xplorer 4LR: The antenna holder allows to use the full antenna cable lenth The GPS holder is for the TBS M8N V2 The Camera is forthe Insta360 SMO4K Update on antenna holder, longer and slimer

Vertical and Horizontal mount for Insta360 Go3. Used support for enforcers only. Enjoy! 8/20/23 UPDATE: Fixed bolt hole at bottom of vertical mount. ... Added new combo vertical/horizontal mount.

A Durafly EFX Racer canopy designed for holding an Insta360 One camera ! ... 5% infill is enough Here is a videos that shows the result : https://youtu.be/L0rU-AwaCOo

Camera mount for Insta360 one r 1-inch mod. The width of the fastening tabs is 3.5mm, the distance between them is 3.5mm aswell. ... The borehole has a diameter of 5.5mm.

20 degree insta360 One R Mount 20 deg Uses the 4 M2s up front, and a single M2 in the rear with a lock nut under the top plate. ... tpu only

This is a backpack mount for insta360 or any action camera. here is the link to the video: https://youtube.com/shorts/FFo9LluqpIU I will put more description soon... ... Thank you

This is my 13mm offset GoPro Extension as featured in Insta360's video featuring @DrewDrones : https://youtu.be/dBFDbwCz4jI You are free to make and use this thingi for your drones and your videos, but not to sell it.

A geprc Mark 4 mount for Insta360 One R. It includes a vertical immortal-T mount. ... It's a remix of three different designsbut, unluckily I can't find them anymore

Insta360 ONE RS 1-Inch Holder/Holster You can carry the camera with the invisible stick and lens cover attached.And You can also hang it on the wall. ...Please remove the supports after printing.

Insta360 One RS 4K lens cover. It has a differently shaped bezel compared to 4k lens that comes with One R. ...While this cover can be forced to fit on One R it was designed specifically for the RS.

Insta360 Go2 mount for printhead https://www.thingiverse.com/thing:5881421 I tried to do so that there were no vibrations, in case I failed, I attach the .stp file upd1: added a stronger version

The Insta360 One R's versatile lens cover has been designed to safeguard the camera module from dust and other debris, ensuring optimal performance at all times. This protective covering can be effortlessly attached to the camera, providing a snug...

The following components are included: - Insta360 SMO 4K camera holder in GoPro style - M3 hand fastening screws and nut normal - M3 hand fastening screws and short nut - M2 hand fastening screw and nut holder - SMO 4K lens cover - SMO 4K lens cover...

Halterung für eine insta360 one R, 1 inch edition. Ich habe Befestigungen zugefügt, um sie an einem Feiyu WG2 Gimbal zu montieren. Die kann man natürlich auch weg lassen und jede andere Halterung anfügen. Bracket for an insta360 one R, 1 inch...

... find one so I designed this. ... This fits the Flywoo Explorer LR HD v2. You can install the Insta360 go 2 power holder on this. This video was recorded with the Insta360 Go 2 mounted with this mount and stabilized. ... https://youtu.be/fsTuCGyN9Ww

The model is 0.2-0.3 mm larger than the speaker itself. Even like this the fit is really snug, needs a bit of force to fit. With PLA or PETG it may be a bit large, adjust the size according to your printer setup.</p><p>Printed with Ender 3V2, volcano...

To take full advantage of its capabilities, simply place the Insta360 Nano in a base that can be secured using three rubber bands, or attach it directly to your tripod head via an arca-swiss mounting plate. ... Printer Settings: Dremel Rafts: Doesn't...

This is a custom mount for the RMRC Recruit, designed specifically to accommodate an Insta360 One where a GoPro would typically fit. To make it work, you'll need to modify both the lid and the front cowling of the mount. Additionally, reinforce the...

This is a Lens Cover and a stand for the 360 ° - Cam Insta360 ONE X2 and its based on the stand for the Insta360 ONE made by Lensrentals published here: https://www.thingiverse.com/thing:3935516/files Because the One X is smaller than the One X2 i...

I designed this little adapter as I have an Insta360 ONE R and couldn't use it with my GoPro accessories. The originals GoPro screws can be used but you will need a M5 nut to lock it. Printing : Easy to print, no brim, no support. ... I suggest...

Two customized Insta360 mounts designed specifically for a Project 399 Super G+ camera system, offering enhanced flexibility and versatility. The first mount features a 45-degree forward tilt, allowing for dynamic and engaging perspectives. ...In...