tinyhawk 2 insta360 go 3d models
975614 3d models found related to tinyhawk 2 insta360 go.
thingiverse
Immortal T teams up with Insta360 to create a custom mount for the Armattan Japalura drone, printing it directly onto the camera using TPU. ...With 100% infill, the result is a rock-solid structure that eliminates any jelly-like vibrations in their...
thingiverse
... There's a video on YouTube: https://youtu.be/XYTrkwBv1F4 I printed it both in PLA and PETG, and both work perfectly. My preferred layer height is 0.15mm. You'll need 2-2.5mmx27mm screws for assembly or do it as @cavirules did - use filament.
thingiverse
Mount your Insta 360 Go camera securely onto a Beta 85 frame using its innovative lock-and-go system, which eliminates the need for any additional fasteners or adjustments. ...Simply snap the camera into place, and you're ready to capture stunning...
thingiverse
This is a Camera mount for the Insta260 GO for the Iflight Chimera 4 micro long range quadcopter. Print in TPU at 70% infill. Supports are needed. Check out my review video on YouTube. Link in bio. ...
thingiverse
Insta 360 Go with new [Twist-Lock V2](https://www.thingiverse.com/thing:3939555) mount available for download. Open Source design allows users to modify parameters, including plate thickness, lock thickness and angle. Download the Fusion360 file...
thingiverse
BN220 GPS holder for Emax Tinyhawk 2 Freestyle
thingiverse
... grass). TPU printed at a layer height of 0.2mm with 20% infill, scaled up by +1-2% for a snug fit around the camera mount, which was quite tight even at the lowest scale setting. ...Scaling above +1% became impossible due to the design's geometry.
thingiverse
Materials List: AirFrame: http://ritewingrc.com/product/ritewing-drak-nano-extended/ Laminate: http://ritewingrc.com/product/rw-lf-laminate-film/ Flight Controller:...
thingiverse
Remix of the Emax Tinyhawk 2 Freestyle Cinewhoop Duct by bb028114.
thingiverse
This is a transfer of a tinyhawk 2 freestyle II top part of frame (whatever the heck the 2nd generation tinyhawk is called, this is for it :) Updates pending If you like this, like , follow or donate please thanks :D
thingiverse
Antenna and battery cable holder for the Tinyhawk 2 Freestyle, works good with some rubber band holding the battery cable in place
thingiverse
canopy for tinyhawk 2 fc with a mount for the Runcam Thumb. ... Work in progress added sideplates for nano2 camera added botgrinder logo Build link: https://rotorbuilds.com/build/29742
thingiverse
Tinyhawk 2 20x20 Stack mount adapter. Designed because the flight controller boards kept frying on the tiny hawk. ...It uses the same screw holes all that is required is some M3 screws and nuts.
thingiverse
This is an adapter I made to mount a happy model f4 1s 12a aio fc on the tinyhawk freestyle 2 frame. ... This should work for any fc with 25.5mm mounting holes.
thingiverse
Feet for Tinyhawk 2 combined with an immortal T holder that was designed for the Amarten Tadpole frame. You'll need to flip both prints to make a complete set. ...
thingiverse
This is a prop guard for Tinyhawk Freestyle 2 that don't need you to remove the motors/screws. I'm still improving the protection area without increasing the weight so much. Mirror print for opposite side. Print on TPU. ... facebook.com/FPV3DPrints...
thingiverse
A Lollipop Mount for the Tinyhawk Freestyle 2 that just slides on the back 2 mount bars. It can be mounted while the antenna is already soldered to the VTX. PLA/TPU (TPU for flex) For PLA is has to be printed exactly like the Picture from Cura,...
thingiverse
Detachable whoop for Tinyhawk Freestyle 2, may fit first version, but can't check. You just put it over the frame and secure with the same strap as the battery. It is not a full whoop, it is still possible to put fingers into props, but you can...
thingiverse
Printed sideways (so the plate is vertical!) for better strength! This is meant to be secured at the back with a cable tie in addition to the front frame screws and the upper camera cage standoff. ... Here is a video which was recorded with this...
thingiverse
I printed it in PETG, 0.6 nozzle and 20% infill. Any nozzle size will do. No supports required. ...Printed standing up as it would be mounted to the servo
prusaprinters
<p>I printed it in PETG, 0.6 nozzle and 20% infill. Any nozzle size will do. No supports required. ...Printed standing up as it would be mounted to the servo</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Creality</p> <p...
thingiverse
I just a (beginner) remix from angryDon for runcam nano3
thingiverse
Tinyhawk 2 FS has some small design flaws in regards of dangling antennas and also the battery is hard to strap and sometimes flies out when crashed. This is second iteration and can be definitely ironed out and make more adjusted to fit the frame...
thingiverse
This protection provides secure placement for a RunCam DVR-S module under the TinyHawk 2 Freestyle frame. It may also work well with 20x20 split cams, but I haven't tested it since I don't have one on hand. To set up the DVR, attach double-sided tape...
thingiverse
After i installed an runcam thumb on my tinyhawk i wasn't able to moun the battery so i designed this and its better balanced now
cults3d
Youtube Video Propeller Guard for EMAX TinyHawk 2 Freestyle FPV Drone. I've designed and tested many variances with corrections of this propeller guard until this version. - Strong: It survives many crashes while protects the drone and propellers. -...