tinyhawk 2 insta360 go 3d models

959512 3d models found related to tinyhawk 2 insta360 go.
Tinyhawk 2 Insta360 Go mount
Tinyhawk 2 Insta360 Go mount
thingiverse

I swiftly grab my Insta360 Go to attach it securely to my Emax Tinyhawk 2. Check out the video of this setup at https://youtu.be/yzbDfY_CZGA. You can find more information about the Insta360 GO camera at...

Tinyhawk 2 insta360 go upright mount
Tinyhawk 2 insta360 go upright mount
thingiverse

replaces stock camera mount and holds insta360 go upright behind it for fpv mode video

Tinyhawk 2 Insta360 Go camera mount (quick-connect)
Tinyhawk 2 Insta360 Go camera mount (quick-connect)
thingiverse

A remix merging [heecheee](https://www.thingiverse.com/thing:4376399)'s snug-fitting mount for the Insta360 Go with [anarkistix](https://www.thingiverse.com/thing:4434905)'s clever way of mounting the camera, via clipping into existing holes in the...

Tinyhawk 2 Freestyle Insta360 Go Mount
Tinyhawk 2 Freestyle Insta360 Go Mount
thingiverse

Tinyhawk 2 Freestyle removable and adjustable mount for the Insta360 Go. Designed to be printed using TPU, Not sure about the tolerances using PLA etc. No supports needed. I wanted something that was easily removed and had plenty of...

EMAX Tinyhawk Freestyle 2 Insta360 Go Mount (35 degree)
EMAX Tinyhawk Freestyle 2 Insta360 Go Mount (35 degree)
thingiverse

print with tree support and remove the support with a scalpel remix of https://www.thingiverse.com/thing:4621416

Insta360 Go Tinyhawk 2 Race mount holder
Insta360 Go Tinyhawk 2 Race mount holder
thingiverse

https://www.insta360.com/sal/go?insrc=INRO7M1 The primary intention of this mount is to be installed under the Emax Tinyhaw2 Race, utilizing the lipo strap. ...This particular design should also fit other models that use a toilet tank-style lipo...

Insta360 Go 2 Tinyhawk Freestyle 2 mount.
Insta360 Go 2 Tinyhawk Freestyle 2 mount.
thingiverse

One piece mount for the Insta360 Go 2. No jello, with good ventilation in the back (also incase your camera gets stuck). Secures with a rubber band. You should add a ballast to the back for increased performance but I can barely tell the camera is...

TinyHawk 2 Freestyle silicone insta360 go camera mount
TinyHawk 2 Freestyle silicone insta360 go camera mount
thingiverse

It works great, and it is much more durable than pla or tpu. To make it print the mold, then mix type 1 silicon (the acetic one) with about 10 drops of food coloring. Next step is kind of optinal, depending of what you want the final product to...

Insta360 GO Mount for EMAX Tinyhawk 2 Race
Insta360 GO Mount for EMAX Tinyhawk 2 Race
thingiverse

... thicker stands may offer better stability but also add extra weight. The original design idea comes from a Thingiverse project (https://www.thingiverse.com/thing:4326890), which unfortunately didn't fit on the Race 2 edition due to its taller fin.

Insta360 Go clip on for EMAX Tinyhawk 2 - horizontal
Insta360 Go clip on for EMAX Tinyhawk 2 - horizontal
thingiverse

The Insta360 Go camera is attached to the EMAX Tinyhawk II, capturing a horizontal angle.

Insta360 Go clip on for EMAX Tinyhawk 2  - vertical
Insta360 Go clip on for EMAX Tinyhawk 2 - vertical
thingiverse

The tiny Emax Tinyhawk II drone is now equipped with a sleek Insta360 Go camera.

Insta360 Go 2 mount for Emax Tinyhawk Freestyle
Insta360 Go 2 mount for Emax Tinyhawk Freestyle
thingiverse

This allows you to mount an Insta360 Go 2 on your Tinyhawk Freestyle. It reuses the factory screws. Print it in a flexible material like TPU, or you'll get jello. There are cutouts for magnets, but I don't recommend using them. They'll pop loose...

Insta360 GO Mount for Emax Tinyhawk Freestyle 2
Insta360 GO Mount for Emax Tinyhawk Freestyle 2
thingiverse

Per request. ...Here is a version of the Freestyle 1 mount with correct spacing to fit the Tinyhawk Freestyle 2.

Insta360 Go 2 Mount for EMAX Tinyhawk II Freestyle
Insta360 Go 2 Mount for EMAX Tinyhawk II Freestyle
thingiverse

Will fit the Insta360 GO 2 snugly enough to not fall out during normal flight. It depends on a friction fit so you may need to fine-tune the upper and lower contact pads depending on how well dialed in your printer is. This mount is designed to...

Insta360 Go 2 Tinyhawk Freestyle 2 mount version 2
Insta360 Go 2 Tinyhawk Freestyle 2 mount version 2
thingiverse

Print with tree supports preferably. Print mount in upright orientation. Soft mount with double sided foam tape on the bottom (remove protective backing at personal preference, I did not remove). Top side soft mount is two spacer o-rings. Rig is...

Tinyhawk II Freestyle Insta360 GO Mount
Tinyhawk II Freestyle Insta360 GO Mount
thingiverse

After trying a few designs off here and finding they still caused jello, I designed my own. ... This is Zip Tied on so it wont suit everyone. NOTE: This is for the insta360 Go. ...Not the Go 2

Insta360 GO 2 Mount
Insta360 GO 2 Mount
cults3d

Simple one hole mount for the Insta360 GO 2.

Insta360 Go 2 Mount
Insta360 Go 2 Mount
cults3d

Mount for the Insta360 Go 2 (25 degrees, 30 degrees) for the GEPRC Cinelog.

Insta360 GO 2 Mounts
Insta360 GO 2 Mounts
thingiverse

This is my simple ring mount for the Insta360 GO 2 designed for M2 hardware.

Insta360 Go 2 Profil
Insta360 Go 2 Profil
thingiverse

Just a simple profil circle for the New insta360 Go 2. Remix it to make your own mount. ... Print in TPU

Insta360 Go 2 mounts
Insta360 Go 2 mounts
thingiverse

Ḿounts for the insta360 Go 2 camera that works with my base mounts, for example this one: https://www.thingiverse.com/thing:4377050 Print in TPU Note this is still untested as my go2 have yet to arrive. ...It's based on the official Go 2 model from...

Insta360 Go 2 Holder
Insta360 Go 2 Holder
thingiverse

Designed to work with the Insta360 Go 2. Openings to install 2 .375 in. Dia. x .06 in. Thk magnetics. and 8 in. x 1/4 in. ...velcro "One-wrap Ties".

Insta360 Go 2 Case
Insta360 Go 2 Case
thingiverse

This is a case to store an Insta360 Go 2 camera and the pendant. I printed it on a Creality Ender 3 V2 in PLA. Blue for the base and clear for the top. ... Shouldn't need support so long as you print the top of the lid on the print bed.

Insta360 Go Mount for EMAX Tinyhawk II Freestyle
Insta360 Go Mount for EMAX Tinyhawk II Freestyle
cults3d

This is my mount to put an insta360 onto a Tinyhawk II Freestyle. It has the correct spacing for the wider frame of The TH Freestyle 2. ... It can be printed from TPU without support if you have your printer dialed in.

Insta360 Go Mount for EMAX Tinyhawk II Freestyle
Insta360 Go Mount for EMAX Tinyhawk II Freestyle
thingiverse

This is a custom mount designed to securely attach an Insta360 camera to a Tinyhawk II Freestyle drone. It's specifically engineered for the wider frame of the TH Freestyle 2, ensuring a precise fit and optimal performance. ...The mount can be easily...

Insta360 Go 2 Profil
Insta360 Go 2 Profil
prusaprinters

Just a simple profil circle for the New insta360 Go 2. ...Remix it to make your own mount.</p> <p>Print in TPU</p> <h3>Print Settings</h3> <p><strong>Rafts:</strong></p> <p>No</p> <p class="detail-setting supports"><strong>Supports: </strong>...

Insta360 Go 2 lifejacket
Insta360 Go 2 lifejacket
thingiverse

The most secure method for mounting a Go 2 is to use the Insta360 accessory which physically clamps the camera into a mount when it is attached to a go-pro compatible base -- but this requires fully unscrewing the mount from a base to remove the...

Insta360 Go 2 Armor
Insta360 Go 2 Armor
cults3d

Umagawd 2fiddy: https://cults3d.com/en/3d-model/gadget/2fiddy-gopro-insta360-caddix-hd-cam-mount ImpulseRC Apex 3": https://cults3d.com/en/3d-model/gadget/impulserc-apex-micro-3-insta360-ring-mount 2/13/22 Updated the design to remove material...

Insta360 Go 2
Insta360 Go 2
thingiverse

Insta360go 2 mount small modification from CMONEY. ...Original credit goes to the original owner.

Simple Mount Insta360 anti Jello Tinyhawk Freestyle 2
Simple Mount Insta360 anti Jello Tinyhawk Freestyle 2
thingiverse

Just my design of a Insta360 Go mount for the Tinyhawk Freestyle 2