tinyhawk 2 freestyle props 3d models

Propeller guards for the Tinyhawk 2. Snap-on, no screws required. Durable and strong Approximate weight 27g You will be able to fly the drone at home without breaking the propellers They are reversible, so that if one of the parts is damaged due...

This is a prop guard for Tinyhawk Freestyle 2 that don't need you to remove the motors/screws. I'm still improving the protection area without increasing the weight so much. Mirror print for opposite side. Print on TPU. ... facebook.com/FPV3DPrints...

Propeller guards for the Tinyhwak freestyle 2. I'm using these for indoor flights. Simply Clip on the frame. They slide over the screws. ... Print mirrored for the other arms

Bumper for Emax Tinyhawk 2 Freestyle to protects the screws on the bottom. Printed and tested with 0.1 resolution in petg. Adds around 3g to the quad. ... This model fits for me tight, but maybe you have to scale it a little bit smaller in case...

Yes i use deans :P But this is a way i came up with to use a deans mount and have an antenna stick out the back for Tinyhawk 2 Freestyle (2?) update 8/11/21: Added new and improved xt30 version ATTENTION: MADE TO WORK WITH xt30 or Deans Connectors...

A drop in replacement frame for the Tinyhawk 2 Freestyle frame. This includes only the bottom plate as it is the most likely to break (I broke mine and didn't feel like waiting for a new one). The camera plates will be a bit of a tight fit. Work it...

I had to redesign to accommodate the slight difference in bolt patterns between the Freestyle and the Freestyle 2. Like curdur said in their post, don't use these ducts if you use your Freestyle for freestyle flying. These WILL turn it into a...

Like cudbur said in their post, don't do this if you use your Freestyle 2 for freestyle flying. This will largely turn your drone into a cinewhoop. I also did not spend many iterations as cudbur did. This was a one-and-done type design. **Use at...

A little holder for the stock antenna on the TinyHawk II Freestyle. ...

Thin adapter plate for tinyhawk freestyle quads, additional M2 screws needed.

The included spacers for the Tinyhawk 2 Freestyle's circuit board attachment break off quickly in the event of a crash and replacements are expensive, so I designed these parts myself. ... Maybe one of you can use the same.

Top plate for emax tinyhawk freestyle 2 with a cut out for the usb on a f4 1s 12a aio fc. This also has a holder for an xt30 plug and an antenna. ... 2mm screws thread into the pla holes on the standoffs and holds it on fine saving some weight.

I designed some protectors for my new Tinyhawk 2 Freestyle that don't need you to remove the motors/screws. Printed in TPU they just snap over the arm and fit tight. Printed with support at 0.25mm layer height with a 0.4mm nozzle. I really like...

This is a simple Remix to fit a Fullsize FPV Cam (19x19x19 cm) in your Tinyhwak 2 Freestyle FPV Drone. I added a Jinjiea B19 FPV Cam to my Tinyhawk with 1500TVL. Fits very well and on the first two holes, you cann adjust the Camera very good. ... ...

Tinyhawk freestyle antenna mount. protects against accidental damage that can occur. I printed it in TPU. ...No add-ons are required.

Remixed (https://www.thingiverse.com/thing:4117499) to fit the Tinyhawk Freestyle 2. The hole in the back is big enough to fit 2 1s connectors through. If you want a version without the text just let me know. Printed this in PLA without...

TinyHawk Freestyle II Bottom Plate Frame 3 versions. Close to original frame. 2mm arms supported frame. 2mm thicker than first one with all screws are recessed. "NEW added Top plate .STL If your printer can print dimensions correctly this...

This is a GoPro mount for the Emax Tinyhawk 2 Freestyle. The STL with the GoPro thread built-in is untested (it will be tested when my roommate with the printer gets home). It is meant to screw in just above the camera on the top plate and...

Small sideplate to protect the flight controller from dirt/grass/whatever the props mash up. Pretty weak but flexable. Supports not needed if your printer can do a bit of overhang. Secure at the bottom with zip ties to the bottom plate, use...

... from a design i found on this site. also included is a mount for the insta 360 go 2. together with the clipon propguards(also found here on thingyverse) it makes a nice way to fly safely around people and indoors while carrying the insta go 360 2

BN220 GPS holder for Emax Tinyhawk 2 Freestyle

Remix of the Emax Tinyhawk 2 Freestyle Cinewhoop Duct by bb028114.

Prop guards for the Emax Tinyhawk Freestyle underwent 14 revisions, each one strengthening where it broke. The best designs were carefully crafted. These parts are printed using eSun PLA+ (PLA Pro), a material that performs similarly to ABS. You can...

This is a transfer of a tinyhawk 2 freestyle II top part of frame (whatever the heck the 2nd generation tinyhawk is called, this is for it :) Updates pending If you like this, like , follow or donate please thanks :D

Antenna and battery cable holder for the Tinyhawk 2 Freestyle, works good with some rubber band holding the battery cable in place

Detachable whoop for Tinyhawk Freestyle 2, may fit first version, but can't check. You just put it over the frame and secure with the same strap as the battery. It is not a full whoop, it is still possible to put fingers into props, but you can...

This is an adapter I made to mount a happy model f4 1s 12a aio fc on the tinyhawk freestyle 2 frame. ... This should work for any fc with 25.5mm mounting holes.

One piece mount for the Insta360 Go 2. No jello, with good ventilation in the back (also incase your camera gets stuck). Secures with a rubber band. You should add a ballast to the back for increased performance but I can barely tell the camera is...

... requires the screw holes to be smaller than 2mm. The flexibility allows for a secure fit of the screws. If you print in a rigid filament, you will find yourself fighting to get the screws in. Designed specifically for the Emax Tinyhawk 2 Freestyle

A Lollipop Mount for the Tinyhawk Freestyle 2 that just slides on the back 2 mount bars. It can be mounted while the antenna is already soldered to the VTX. PLA/TPU (TPU for flex) For PLA is has to be printed exactly like the Picture from Cura,...