tile tracker holder 3d models

Holder for the "tile" key fob tracker. Type A, Can be glued to a surface then tracker can be inserted into the side of the holder. ...Type B, base and lid version of above After a couple of prototypes i've found this best printed at about 103% for the...

Holder for the "Tile" key fob tracker. Type A, can be attached to a surface then the tracker inserted into the side of the holder. Type B, base and lid version of the above. ... After experimenting with several prototypes, I've found that printing at...

After countless sofa cushion searches for that darn Apple TV remote I decided to pair it with a Tile Bluetooth tracker and make a case for both of them. I know there are several Apple TV remote styles, so see the picture to make sure this one...

Remix to make the case waterproof (if glued) by closing up the speaker hole with a thin layer. ...As it will be glued, removed bolt holes. Button cannot be pressed when tile in case.

After countless sofa cushion searches for that darn Apple TV remote I decided to pair it with a Tile Bluetooth tracker and make a case for both of them. I know there are several Apple TV remote styles, so see the picture to make sure this one works...

The user designed a protective holder for the Sticker model of Tile tracker. To install the tracker, they paused the print process temporarily at the top few millimeters, allowing them to insert it securely within. ...The exact steps to incorporate this...

This add-on is designed to attach to the exterior of the drone beneath its landing gear and closely resembles the Tile Style tracker in terms of design. The adapter has been thoroughly tested with the Phantom 3 Standard, 4K, Advanced, and...

Took this basic holder and added a depression to hold a small tile tracker to the back. ... After using it a bit I reprinted it .5mm smaller which worked a lot better to hold the cards in.

I've had a tile stuck to my old badge card holder, but it worked despite looking really ugly. This is my first 3D print - or remix, so don't be too hard on me. I added a backplate to the card holder and made a compartment for a tile slim inside. ...It...

Keychain holder/Adapter for the Tile Slim bluetooth tracker. By looping a carabiner or keychain loop through both holes at the top, it will stop the tile from sliding out. ... Printed vertically with no supports and no issues.

The button can also be printed slinghtly larger if printed in resin on the x and y axis, however I printed it accordin to the project, and it turns out just as good I opened the tile, which had a dead battery. I replaced the battery, a standard...

This is a DIY Tile Tracker accessory. ...I experienced difficulties adding trackers to everyday items such as my pet dogs, cats, purses, cars, trucks, and other belongings, so I designed these to link up and they work perfectly well there are 2 versions...

My objective was to design a case that could securely hold a Tile tracker while maintaining a low profile and remaining comfortable enough to be carried in a pocket. To accommodate charging needs, I included an offset version with the bottom hole...

This compact Bluetooth device, named Tile, assists in locating common items swiftly. ...With its user-friendly application, you can easily find possessions such as your mobile phone, keys, or wallet within moments.

Replacement Tile Tracker (original) case. ...Replace your long dead battery!</p> Category: DIY

My kid got me a Tile Tracker for Christmas so I slapped it on my bike. The only spot to stick it was under the seat. Print out the part (tweak the dimensions if your seat support is different) and then secure with foam tape and zipties. There's a...

The Tile tracker is an awesome device. I love mine, but I'm not too fond of the fact that they're designed to be disposable. When the battery dies, you're expected to buy a new one for around $25 each, which can add up over time. Personally, I'd...

Track Your Replacement Tile's Vital Signs - Time to Breathe New Life into That Dead Battery!

The newly added file, "35 35 6.2," accurately reflects the dimensions of this enlarged Tile. Since I cannot verify the print's fit, please report if it works or requires adjustments. ...The original file is designed for the Tile Mate, created using...

This slim tile tracker conveniently fits into a compact ID badge holder, allowing users to easily access its button while keeping their identification secure and visible.

Simple case for an Apple TV remote with enough room for a Tile tracker

... keys to the stethoscope. I designed this for my aunt using a model for the Tile tracker holder and one for a stethoscope clip, which can be found below. 1. https://www.thingiverse.com/thing:4019162 2. ...https://www.thingiverse.com/thing:2223056

If you use the Tile Pro tracker to keep track of your pet, whether it's a cat or dog, use this case which helps the Tile Pro attach to your pet's collar. Great for keys and bags as well! Comes with 2 buckles (one for cat, one for dog). Just use a...

 I have two young pooches who like to chew stuff so any sort of “dangly” version of attaching the tracker to their collars is a recipe for vacuuming up very tiny pieces of a Tile Sticker off of my floor ;-)   Prints easily without supports, just make...

Modified original design to fit tile mate (2020 with changeable battery)

Bicycle bottle cage holder for the Teltonika TMT250 Tracker

Glass Tile Holder for Spectrophotometer Calibration

A holder for the letter tiles available here.

A holder for the letter tiles available [here](https://www.thingiverse.com/thing:5398449)

This holder part (tutucu, in Turkish) is used to make the height of the tile as same as the other tile that it's placed under. There is also a wedge that helps to stabilize the tiles and cut the upper part of the holder. Thus leaves the smooth...