throw lever for scope 3d models

It makes zooming IN/OUT much easier (even in gloves) :)Uploaded model (both versions) has these parameters:inner diameter: 46,0 mmI use this throw lever on my rifle scope Vector Optics Matiz 3-9x/50mm but it can be used for any other.If you need to...

Throw lever designed to fit Leupold VX-3 and VX-iiiL scopes, however it most likely fits other Leupold scopes as well (scopes with a ≈ 37.7 mm zoom ring and the gas inlet notch). At full magnification, the throw lever has good clearance for both the...

Quick zoom adjustment aid lever for shooting scopes. Lever made of PET, a more resistant printing material than usual. Files available from 38mm to 48mm. ... Accessories: 1 Allen screw M3x20, 1 Nut M3 If you want a diameter in articular let me...

Throw the lever for Meopta's K-Dot 1-4 and its variation, the Meostar R1. It works seamlessly, having been put to use for an extended period in cold temperatures without malfunctioning. ...A crucial requirement for this setup is a M3 machine bolt and...

-------------------------------------------- This throw lever is modified for use with the Vortex Viper PST 1-6x24. It's made a bit tighter than usual, so attaching a vinyl tape to the scope when installing makes it easier to slide in and install...

The magniffication zoom is really hard to move so throw lever is "must have" for this scope. To do my own throw lever I used "Primary Arms 4-14x FFP Scope (1st gen)" from PoniesWhee because its quite minimalistic and I like how it look. I made some...

Insert the nut into the cavity of the Scope Throw Lever for Vortex Viper PST Gen I, then grind off any excess material with a precision tool. ...Next, cut the M2.5 screw to the precise length required using a high-quality cutting instrument.

scope throw lever for Leupold Rifleman 3-9x40 designed to fit over a 36.2mm adjuster. I used a M3x8mm bolt, but you could probably use a 5mm I added two M3 washers in the gap to prevent over tightening the ring two edges would not take a...

The zoom's high magnification makes it tricky to adjust, so a throw lever becomes an absolute necessity for this scope. To create my own throw lever, I drew inspiration from the Primary Arms 4-14x FFP Scope (1st gen) by PoniesWhee, which boasts a...

You can customize everything from the length of the throw lever, to the position of the clamp to the angle and depth of the scope notch. Best part is all you need to do is install Fusion360 and figure out how to load the step file. (not rocket...

This is a scope ring lever for the Monstrum G3 1-3x24 FFP scope. ... It is deliberately a very tight fit, and will require patience and mechanical persuasion to install.

You can customize various aspects of the throw lever design, including its length, clamp position, scope notch angle, and depth. The best part is that all you need to do is install Fusion360 and figure out how to load the step file - not rocket...

Extended lever for UUQ 3-9x rifle scope from Amazon. Zoom adjustment was hard to turn, and the regular lever was too small. ...This slides straight on the back of the scope, from the rear, for a tight fit over the adjustment wheel.

The Vortex Optics Viper PST 6-24 scope features a robust design and exceptional optical quality, making it an ideal choice for long-range shooting applications. ...On March 29, 2017, the addition of a detailed SketchUp model further enhances its appeal...

scope throw lever for a Swarovski Z5 rifle scope. ... 2mm cap screw and nut required.

I wanted a larger throw lever than what was available on my CVLIFE Scopes(https://a.co/d/29N7bz1). Let's the gun go into my cases. Uses M3 x 12mm Screw and nut. ... Added V2 which is thinner and more rounded for lower profile scopes.

Throw lever for a burris 3x9x40. Takes a 3mmx10mm screw. Can probably be threaded into the plastic. ...I used a brass insert.

Decided to Design my own throw lever rather than pay $30 and get one that only hopefully works. Uses an M2 nut which is inserted with the printer paused and a 12mm M2 hex socket cap screw. Can only guarantee it will fit on the specific model listed...

Athlon Scope Throw Lever for the Argos 6-24x50 scope.

A custom throw ring made for a Vortex Diamondback scope. Specifically the 6x24x50. I don't know if this will fit others. Made for 0.2 layers without supports. Uses two m5 nuts and bolts to clamp onto the magnification ring. ...Included the solidworks...

This is a simple throw lever for the Monstrum G3 6-24 Scope. ... All you will need is m3 bolt and nut to install it.

Throw lever to fit the Bushnell Elite 4500 scope. ... Print on it's side without any support.

This zoom throw lever fits perfectly on the Athlon Ares ETR 4.5-30x56 rifle scope, requiring minimal adjustments to ensure a precise fit. It is compatible with M3 thread inserts measuring 4 mm x 5 mm. ... Printed successfully from both PLA and ABS...

A throw lever designed for the Athlon Ares BTR Gen 1 scope. ...It should also fit the Ares ETR Gen 1 and the Midas Tac, although I have not tested that.Hardware required:1 M3x10 screw1 M3 nutCategory: Sport & Outdoors

This is a throw lever designed for the Athlon Ares BTR Gen 1 scope. It should also fit the Ares ETR Gen 1 and the Midas Tac REVIII, although I have not tested that. ...   Requires 1 M3x10 screw and 1 M3 nut.

I'm trying out the magnification throw lever that fits my Sig Tango 6 4-24x50 scope. I'm not sure if this will fit other SIG scopes in the tango line or their other models, so I'd appreciate feedback from anyone who tries it on different SIG scope...

This is a precision-crafted slip-on scope throw lever extension designed exclusively for the Vortex Strike Eagle 1-6x rifle scope. It offers an ultra-snug fit, making it unlikely to work with any other scope brand or model. However, if you have a...

This zoom throw lever is specifically designed for the Vortex Strike Eagle 1-6x rifle scope. Due to its snug press fit, you may need to adjust your printer's scale settings to achieve optimal results with your chosen filament. For me, it works...

This lever is specifically crafted for the Athlon Ares BTR Gen 1 scope. It should also be compatible with the Ares ETR Gen 1 and the Midas Tac REVIII, though I haven't tested it on those models yet. Required hardware includes: 1. An M3x10 screw 2.

Primary Arms Scope Throw LeverSLx6 Silver Series 1-6"Beefy" to last awhileRecommend course screw of appropriate size and length.Starter hole provided, Predrill hole to avoid cracking.Will clear mid height scope rings in higher. ... Probably won't work...