three pin plug 3d models

You see, I was tinkering with a project where just the sockets would do the trick, so I figured I'd give modeling this power plug a whirl as a challenge to myself. What's it got? Well, for starters, some threads and winglets that make it super easy...

This instruction details an alternative design to a previous plug enclosure, featuring no need for screws. The cable roll can be made using DE-9 connector or 15 Pin (VGA), printed with ABS on a Makerbot 3D printer. Epoxy is used to assemble the shell...

... $3.54. The Hirose website offers a basic CAD model, but this detailed model includes all components such as pins, shield, lock, bend relief, strain relief, housings, and screws. ...Mating receptacle CAD models can also be found on the Hirose site.

Once the pins were securely attached, they were inserted into the connector from the rear side, allowing me to pull them out on the front where they snugly fit if they protrude sufficiently. The soldered wires prevented the pins from being removed,...

Dude, I'm checking out this sick little 2-prong 5 amp plug.

Snag-proof design with 0.1 inch pin spacing ensures smooth usage.

You can use this dummy plug to secure unused male sockets in GM vehicles. ... I use it do blank a EGR valve at my Opel Astra.

I needed to replace an Earth pin in a door bell that had been stood on while unplugged. This was the shape of it. Maybe it will fit other devices that require the earth pin replacing. Little stop measures 5.15mm deep and adds on 6mm height to...

This internal component of the Ratio Electric Mennekes Type 2 plug holder secures the plug using a latch, and it's installed within the holder with a spring-loaded mechanism. ...Due to its failure, I created a custom replacement for this crucial part.

The plug on my trailer was always in the way when it wasn't connected to the car. I designed this in Tinkercad. ...It was printed on the new Kywoo Tycoon Max.

I wanted somewhere to hold the plug/lead and the safety cable so I added strengthened wings to his design with holes for rivets or screws and a raised column with a ball on the end to hook the safety cable over. ...It'll probably hold a chain / D ring...

... of a subs use of the wand. ... To use as a punishment simply make the sub lock up the plug using an anti tamper seal, send a photo showing the no. ...of the seal and the plug locked, then only allow the sub to remove the tag after a period of time.

I found a good “cap” for the plug made by ksd050 on thingiversehttps://www.thingiverse.com/thing:4804261I added wings and right angle support, holes for rivets / screws and a column to hook my safety change for out caravan on to.A D Shackle for a...

It's a convenient storage solution for your cable and an ideal replacement if you've misplaced or broken the original pin. To use, simply print it out and insert it into place. No additional adjustments are necessary. The open-source .SCAD file was...

To make it happen, do the following: Print out a pin using ABS material, or choose any other material that suits you. Next, attach a flat surface mount to the top of the pin by sticking or gluing it firmly in place. Finally, take your GoPro with you...

Its so well made that it just fits perfectly but I wanted somewhere to fit the plug when the caravan was parked up. I added a couple of wings and 5mm holes for rivets with some 90º supports. Then I put a ball on top of a cylinder to put the safety...

... pry open the female side of the connection, making small adjustments as needed. To create a polarized connection, use both male and female terminals on one side of the plug. ... Female terminal dimensions approximate 6mm x 2.5mm x 14mm (3/16 inch).

Customized version of https://www.thingiverse.com/thing:213946 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=213946

A personalized version of http://www.thingiverse.com/thing:213946 was crafted using the Customizer tool (http://www.thingiverse.com/apps/customizer/run?thing_id=213946). The customization process involved setting backlash to 0.5, object number as 3,...

A personalized rendition of http://www.thingiverse.com/thing:213946 was crafted using the Customizer! (http://www.thingiverse.com/apps/customizer/run?thing_id=213946). The settings included a backlash of 0.5, 'Write' font from 'Letters.dxf', and font...

Customized version of https://www.thingiverse.com/thing:213946 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=213946

Customized version of https://www.thingiverse.com/thing:213946 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=213946

Customized version of https://www.thingiverse.com/thing:213946 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=213946

Musecon, a sci-fi/maker/filk convention in the Chicago area, is hosting its third event in August. Attendees can expect a weekend filled with activities such as blinkenlights run by 2D kits, singing Tesla coils on Friday evening, and panels on...