threaded rod socket 3d models

Here is my design for spool wall holders using an M8 threaded rod. The spools sit atop the rod and touch the wall with their backside. This design enables easy removal and installation of the spools from the shelf. While it may not be visually...

http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: Head height: adjusted to provide better clearance Counter-sink: deepened by 2 levels to increase thread visibility Non-thread length: maximized...

Three 20cm long pieces of M8 threaded rod (Tip: check dollar stores or similar for low prices on 1m rods). A tool to cut the M8 threaded rod (a hacksaw will do fine). Alternatively, ask a local auto shop or school to cut these if none of your friends...

A printable alternative exists (https://www.thingiverse.com/thing:2176224), but I prefer the added strength of threaded rod and not wasting precious time printing a potentially weak upgrade. I'm more than happy to modify for other rod sizes if...

This is a remix of the Paint mixer/stirrer by Splicing, tweaked for use with threaded rod. The original design featured a low profile that would print quickly, but I wanted to attach this to some rod and have the bottom be flush. To achieve this, I...

http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: nut_resolution is set to 0.5 thread_step is set to 2 slot_depth is set to 2 nut_thread_outer_diameter is set to 7 type is set to nut...

http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: resolution is set to .5 non_thread_diameter remains at default -1 nut_height is set to 6 type is a bolt thread_length is set to 10 drive_diameter...

Other dimensions include an inner diameter of 8 mm, a nut diameter of 12 mm, thickness of 2 mm, countersink of 2 mm, a nut resolution of 0.5, nut step shape degrees of 45, nut thread step at 2, hex head type, normal nut type, a thread step of 1.27,...

http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following settings: Thread step is set at 2.5. Washer type selected. Nut height is 6 units high. Thickness of object is 2 units. Step shape degrees are 45. Wing...

- Modify the nut thread outer diameter to 9 units. - Alter the nut thread step count by 2 units. - Adjust the non-thread diameter to 17 units. - Exclude any texture from the customization options. - Set the thread step at 1.27 units. - Optimize for a...

http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the Following Options: non_thread_diameter Set to 0. drive_diameter Defined as 5. head_diameter Identified as 12. nut_height Configured at 6. nut_thread_outer_diameter...

... ...I needed to attach it to an 8mm threaded rod, so this is what I came up with. It utilizes the mount support that comes with the Titan (at least mine does, which is a Chinese clone). Please verify that your mount support has 30mm between hole axes.

http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: thread_length = 55 slot_width = 1 nut_step_shape_degrees = 45 step_shape_degrees = 40 head_height = 5 resolution = 0.3 drive_type = socket...

... risk; thorough load testing has not been conducted. The accompanying images showcase the part printed at 50% scale, demonstrating a seamless fit with 1/4" threaded rod. ...At this reduced size, the mounting holes accommodate 6-32 bolts perfectly.

I use it with a M4 threaded rod so I enlarged it slightly (initially, I thought I had m3) It provides significantly more stiffness to the extruder arms and as an added benefit you can adjust the hole-to-hole distance very precisely with the threaded...

This is my go-to cable clip or guide that makes it easy to keep the cable of a Nema 17 motor neatly organized along the bottom of the M8 threaded rod in @henryarnold's Drawing Bot setup.\r\nI utilize a total of 10 clips to expertly guide the cable to...

This is a version of the Z axis mount for using M6 Threaded rod with your MendelMax Z stage motors. It utilizes smaller M6 Thrust Bearings instead of the M8 ones used on MendelMax or the 608 bearings found in the original AlephObjects version. I have...

Frame Support for M10 Threaded Rod It is installed on the upper plane of the frame and on the front plane of the frame. Secured with two screws, M10x20, and T-slot nuts. This feature enhances the overall rigidity of the frame, eliminates unwanted...

To suit the lasercut part with threaded rod passage, its design was altered. I created two length options to cater to users with restricted space while homing the z-axis; I opted for the long one due to longer springs. ...The original Solidworks file is...

The 10mm hole on the CTC Prusa i3 is a problem when the x carriage hits the lower parts, causing the 8mm threaded rod to rattle. This bushing solves that issue exactly. I designed this solution using OnShape. It's part of my project to improve the...

This upgrade simplifies adjusting the Y-axis belt tightness for Prusa style printers with threaded rod frames. Print one main body plus two wallons to complete it. ... To function, you'll need: 1 x Bearing 608 (for the belt) 1 x M5 screw and nut (for...

It securely holds an M8 bolt in place while allowing a threaded rod to pass through its center, enabling me to harness the power of a stepper motor for linear motion. Print Settings Printer Brand: RepRap Printer: Prusa i3 Rafts: No Supports: No...

Flexible (filaflex) coupling for Z-axis, 8 mm threaded rod. It works seamlessly! Say goodbye to the frustrating Z wobble effect and noise! This solution is extremely affordable and effective. No bolt required - simply rely on pressure to ensure...

Flexible Z Axis Coupling for Smooth Prints Get a solid grip on your Z axis with our flexible coupling solution, perfect for 8mm threaded rods. This ingenious design eliminates the annoying wobble effect, ensuring your prints come out smooth and...

I decided to remix the MP Select Mini Threaded Rod De-Wobbler Coupling from USWaterRockets, scaling down its diameter because I only had smaller #04 hose clamps available. These clamps have an opening range of 5.6 to 16mm in diameter. ...The coupled...

http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following settings: Thread Length is set at 25 millimeters. Normal Nut Type has been selected. Outer Thread Diameter measures 10 millimeters. Model Resolution is...

Extend the threaded rods at the back of the X/Y bed by 170mm, about 85mm on each side, for optimal installation. Both parts are printable without support, although importing may require adjusting orientation due to possible offset issues. Print...

To complete it, I needed an M8 threaded rod, two bolts, and a spring - it actually works perfectly! At the top, there's a bearing labeled 608zz. Not to mention another one, labeled lm8uu. Printable space is set at 500 × 500 mm. Originally, Z-axis...

I needed an 8mm threaded rod to attach it, so I came up with this design. It utilizes the mounting support provided with the Titan (at least mine, which was a Chinese clone). Please verify that your mounting support has 30mm between holes on its...

I've crafted innovative herringbone gears tailored for use with the Ormerod printer, focusing on converting the z-axis threaded rod into a robust 8mm lead screw. You can easily integrate a standard lead screw nut and/or grub screws to enhance...