threaded rod end caps 3d models

10 mm threaded rod end cap, to protect from sharp edges of the cut threaded rod. ...I used these on my Prusa i3 printer build.

10 mm threaded rod end cap, to protect from sharp edges of the cut threaded rod. ...I used these on my Prusa i3 printer build.

10 mm threaded rod end cap, to protect from sharp edges of the cut threaded rod. ...I used these on my Prusa i3 printer build.

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=64275 Instructions Using the following options: Tube_Outer_Diameter = 8 Tube_Inner_Diameter = 6 End_Diameter = 8 End_Thickness = 3 Tube_Height = 10

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=64275 Instructions Using the following options: Tube_Height = 8 Tube_Inner_Diameter = 5 End_Thickness = 3 End_Diameter = 7 Tube_Outer_Diameter = 7

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=64275 Instructions Using the following options: End_Thickness = 4 Tube_Height = 12 End_Diameter = 13 Tube_Outer_Diameter = 13 Tube_Inner_Diameter = 10

Cap device to protect from sharp cut edge on an 8 mm threaded rod. ...Used to cap the rod on my Prusa i3 build.

Cap device to protect from sharp cut edge on an 8 mm threaded rod. ...Used to cap the rod on my Prusa i3 build.

Cap device to protect from sharp cut edge on an 8 mm threaded rod. ...Used to cap the rod on my Prusa i3 build.

The acorn nut serves as a protective measure for the conclusion of a threaded pole, ensuring its security and stability.

I didn't want to buy the end caps at $3-4 each, and the cap to keep the hangers on is same height as a hanger. So, I made me some with extra large stoppers. These are designed to fit closetmaid band rods, 3/4 inch in size. Printed on Anycubic...

A rod end bearing is a form of precision articulating joint, featuring a ball swivel. A bolt or something similar will pass through an opening within the ball swivel and there is either a male or female threaded shaft attached to it. ...The mode is a...

As Puddlefist stated, the 150mm threaded rod that comes with the Anet A8 spool holder is not quite long enough. A longer non-threaded rod is probably best, but this will use what you already have and the rod cannot slip out with normal use. ... ...

3 different rod end caps. ...Rod clamps fit over the smallest one without it having to be removed.

These handles have an ergonomic curve that makes holding easier and also covers the ends of the threaded rods. Additionally, snap-on screw-on end caps are added for safety purposes, especially during demonstrations where little kid's eyes get too...

To remove them just push the centre nobble downwards to release, then keep pushing the cap around further until the rods are at 90 degrees from the cap, they will then come out easily. ... Filament used in the pictures is Fillamentum Vertigo Galaxy...

Our Wire Shelf Rod and End Cap broke. It is used to prevent hangers from falling off the end and protect from sharp edges of wire shelf systems. The local Hardware store was out of stock, so a quick mock-up and it works great. Printed on...

It showcases my MakerBot Thing-O-Matic #5801, named "MiracleMaker," where I've customized the front rod end-caps. You can see an artist's rendering of additional aesthetic and functional modifications in progress. To share these unique parts with...

the caps are also hollow so they can be packed with lead shot, or split shot (fishing weight) the printed one in the photo, doesnt have the threaded caps (same design solid caps) the thread is an M18 2.5 so another option would be to use a piece of...

This text describes an easy-to-open end cap cover for Thing-o-Matic's y and z-axis linear rods. It uses a sliding dovetail joint, with alternative options available online at thingiverse.com. The STL file provides single or double sets of covers,...

When replacing end caps on an Ultimaker 3D printer, I found it difficult to manage the tricky nuts inside. To solve this problem, I used a calumet tool from Thingiverse (http://www.thingiverse.com/thing:44118) to hold the nuts in place. Initially, I...

End Caps for 8mm threaded rod.

The 8mm threaded rod can be used with this product.

M8 threaded inline load cell 1kN 2kN 3kN 5kN tension and compression force transducer.Force sensor model: FL34

Curtain Rod End Cap - Inner Diameter : 20mm

Just a simple end cap to replace some broken ones. ...Suits a 16.5mm rod.

An end cap for the Closetmaid rod (https://www.amazon.com/ClosetMaid-2051-SuperSlide-Adjustable-Hanging/dp/B00KZZ5JZQ). ... This end cap is similar to the Closetmaid end cap (https://www.amazon.com/ClosetMaid-7563800-Hang-Endcap-Pack/dp/B000BQWUCE).

... *Additional info* End cap thread: M5 (incl. the 12 & 12.5mm ID versions). M3 holes through the centre of the end cap to secure the rod (optional) Drawer slide: side mounting - zinc plated - 125kg non-locking (I go through a lot of clothes :P)

Tie rod end for M5 threaded rod RC 1:10, Max Tiger 4x4 to reinforce the tie rod with an M5 threaded rod. ... Print out, cut in the M5 thread and adapt the threaded rod to the length of the tie rod.

Anti-friction cap for threaded rod. Does not impose stress but prevents frictional noise. Used on Anet A6 Z axis. Height 15mm, outside diameter 10mm, inside diameter 8.5mm. ...Reinforcement 2mm in height, 12mm diameter.