thor hammer handle design 3d models

Inside cavity and tubes do NOT need support, but I couldn't model that out of the design, and it would be a BEAR to remove support from well inside one of those tubes. I like using 0.6mm nozzle and 2 walls for faster print. If you use .4 nozzle, go...

At the same time in Germany, the Steiff firm, unaware of Michtom's bear, produced a stuffed bear from Richard Steiff's designs. Steiff exhibited the toy at the Leipzig Toy Fair in March 1903, where it was seen by Hermann Berg, a buyer for George...

Welcome to my latest design to convert an Ender 3 v2 to CoreXY printer. The Aim of this project was to build a converter kit for my V2 model into a Core YX printer and by reusing as many original parts of Ender 3 v2 as possible. The second goal...

There will be friction between the gasket and the sides of the case. To facilitate the ejection of the gasket-mounted plate and PCB from the case, I've incorporated the ingenious thumb port that u/kkatano [https://www.reddit.com/user/kkatano/]...

  The two step design means the same parts work on MTB or road tyres. Optional TPU feet to grip the garage floor. Parts RequiredYou’ll need approx. 3m of 16mm tube per bike – I used curtain rod from Bunning for all the short pieces.  It's cheap and...

I designed this to minimize weight of the wheel. placing K2 clip silhouettes inside the base helped achieve this, plus it provided a way to pop in the slices on the go. I added a plain lid too so you can customize, like I did with my maker...

Medallion, depicting the deity baphomet, that the Knights Templar were accused of worshipping, file STL, OBJ for 3D printers, two sizes two size however, the dimensions can be changed with each slicer composed of 1041 mil points all the files have...

So, I used the spool holder, spool nut, and collar from Tek_3D's Spool Holder that uses 8mm bearings and an 8mm rod and used the lower-profile filament spool holder replacement that mddatthngvrs created as the starting point for designing a set of...

Important note: This design is intended to be used with the electronics box relocated to the back of the printer. Will not work on the bottom as there will be no room for air intake, let alone a fan. Update Apr 1, 2021 Added a version of the left...

 Custom board designs that can be used to order from oshpark or jlcpcb are on the github.All Glass models should be printed with clear filament. I used Sainsmart clear TPU with maximum layer height, 100% infill concentric pattern.  You want...

The main 24V have been extracted from the PSU of the printer itself, so that no additional power plugs are needed. Raspberry Pi 3 Model B+ 1.4GHz 64-bit quad-core processor, dual-band wireless LAN, Bluetooth 4.2/BLE, faster Ethernet, and...

Not being a big fan of the zip tie mounting principle used for the original ball bearings by Prusa Research, I designed these clips to hold the bushings securely in place. They can be printed easily without any support. You can use a brim to hold...

The second part of a new polypanel system (the original system designed by Devin Montes). Combined with V3 Polypanels, these internal panels greatly strengthen structures and create new structural possibilities including honeycombs and cubic based...

I tried that but I'm not terribly patient and I never got results I was satisfied with.These models are designed to support embedding magnets in the hexes. The mold created from “Ring mold” has 12 slots (2 per side) for 1/10" diameter, 1/16" thick...

This should be cleared out when you run the screw  on the knob the first time. any files with a X2 at the end indicate you have to print 2 parts. the Mirrored parts:You can mount the corners and latches on either side.Corner(Gen8)...

I also changed the original rotor design by BbrnKyle very slightly by reducing the height of protruding cone and made the diameter very slightly larger for a tighter fit in the mouthpiece. The rotors are otherwise identical. I included the stl...

I might release a new lid design to fit a different pot, but I'd encourage people to develop their own if they know enough CAD. The lid is made out of 6 different pieces or "petals". Right now, there are three different petals design: * Petal:...

The same applies everywhere in this guide.I designed the carriage and hotend mount this way for stability as the bolts secure the hotend mount as well, preventing hotend roll.Fasten the cables from the heater cartridge to the PCB (from your spare...

The mode running is "Race". Ring Lamp V2 Race mode Key Features: When designing this I had some key features in mind: ° simple and clean print ° avoid the led strips glue tape on the back at all cost. ° add a simple compartment for the electronics....

Please let me also know how you rate the design.Unfortunately, the uber fidget ring was deleted due to a design claim, so its no longer available.If you like it, you can check out  the original print-in-place fidget ring:or the dual fidget...

There can also be found special tunnels leading into the cockpit and MegaCaliber Six turbolaser cannon that were designed by our team for you to easily introduce LED wiring. All the assembly parts are provided in STL files in recommended positions...

......(I put “simple” in quotes because designing this thing and perfecting it has been anything but simple.) My goal was to create a ball clock that could be 3d printed relatively easily on an Ender 3 class 3d printer and assembled without too much fuss.

##Hero Me Mutant V2 HotEnd Cooling System ####Designed to be used with the Wham Bam Mutant V2 Universal Tool Swapping System. ####Learn more about the Mutant V2 here: https://whambamsystems.com/mutant ####Welcome to the Mutant Invasion! The Hero...

Here you are!Designed for use with “Way Basics Eco Stackable Storage Cube, Cubby Organizer (Tool-Free Assembly and Uniquely Crafted from Sustainable Non Toxic zBoard paperboard), White”...

Designed to be carried on a Freight Ten or the articulated Freight Ten Trailer version. ...More cargo for all of you Sci Fy tread heads out there.Freight Ten...

The 3D printing model’s chosen scales are 1:60 for the FFF/FDM version and 1:100 for the DLP/SLA version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 58 parts;- A printed model stands 251 mm tall, 167 mm wide, 198 mm deep;-...

Ring Lamp V2 Race mode Key Features: When designing this I had some key features in mind: ° simple and clean print ° avoid the led strips glue tape on the back at all cost. ° add a simple compartment for the electronics. ° wire management ° easy...

Now this design is definitely a Work In Progress, so don't expect too much, but the idea is that a good 3D printer ought to be able to make such a typeball using the script presented here. I've pre-generated some STLs but if you do your own, be...

The part is also designed to have enough clearance to the heat-break, while the print head is in home position.Cable management:Now it's time to make sure the power cable of the lights don't get in the way of the printer. Since the cable exits the...

The Garrus Vakarian 3D Printing Figurine designed by our contributing 3D artist captures Garrus in the middle of a mission - the vigilante seems focused, collected, and threads carefully with his M-92 Mantis sniper rifle at the ready. The familiar...