thingiverse elegoo mars 3d models

This is a simple solution to move the USB on a non-P/Pro Elegoo Mars to the front. By attaching this clamp externally, you can avoid making significant modifications to the printer itself. Internally, disconnecting the cable from the backing plate...

A replica of the internal carbon filter housing that comes with the Elegoo Mars Pro. The charcoal block is hot glued inside the original and was no longer working to get rid of the resin smell. After removing the filter with some water (it dissolves)...

Here is a handle design so you can lift your Elegoo Mars cover without touching the sides with dirty gloves! I also made a hanging plate so you can hook it to a screw head on any wall and have your machine free to work on inside without cover in the...

A replica of the internal carbon filter housing that comes with the Elegoo Mars Pro. The charcoal block is hot glued inside the original and was no longer working to get rid of the resin smell. After removing the filter with some water (it...

A replica of the internal carbon filter housing that comes with the Elegoo Mars Pro. The charcoal block is hot glued inside the original and was no longer working to get rid of the resin smell. After removing the filter with some water (it dissolves)...

These are mounts for the Elegoo Mars 2 Pro to fix a wireless door sensor to the top of the printer. This will enable notifications when your print has finished and will enable automated power off using a smart plug. Originally I thought I would...

I printed it on my Ender 3, flipped upside-down with supports and it works fine, although on my original Mars the screw is quite inset and not as secure as it's probably meant to be. I'm not too worried though as the knob is large enough to prevent...

Adjusted the base piece for the wider Z column on the Mars Pro

Some tips for printing the sealing with SLA: I never printed any flexible on my Mars 3 or Saturn. I cannot help you here. I would appreciate some feedback on how to print flexibles and the sealing on SLA :-) ** How to use:** Simply place the lid on...

I've taken inspiration from a design by psdesigns, specifically this one: https://www.thingiverse.com/thing:3895021 To create my own version, I've made some tweaks to enhance functionality. The build plate now has an angled corner, which allows for...

I just made a simple knurled knob but the same bolt is used. ...Also added the Elegoo logo to the top.

I simply crafted a straightforward knurled knob, yet it shares the same bolt as its predecessor. ...Furthermore, I incorporated the Elegoo logo prominently at the top.

This is my version of a vat cover I use for my Elegoo Mars Pro (not 2 Pro - not sure if it will fit there aswell). The cover is designed to put on when the vat is still mounted on the LCD and features a flexible/TPU gasket to seal up a little bit...

 It heats the build chamber and not the resin directly, so in cold conditions you will want to pre-heat the printer some time before using it.The Elegoo Mars Pro is obsolete and out of production (though we still use a number of them). If there...

The angle mount that comes with the Mars is adequate but a little fiddly. ... Hopefully this one serves you better Uses M3 x 12mm hardware

This kit is suitable for mars，mars pro，mars C，mars2 and mars 2 pro machines video：https://youtu.be/m1AdmriOOnQ Detailed list: switch（KCD1 15*21mm Mini Black 4 Pin two position toggle switch）*1 DC Jack（5.5mm x 2.5mm）*1 DC power cable splitter one...

The simplified design is based on: https://www.thingiverse.com/thing:3442165 and https://www.thingiverse.com/thing:4737945 with the aim of being easy to print on FDM I used the same hardware as listed in the top project, the only change I made was...

The desired voltage output should be measured at ~12VDC.Disassembly:Remove the (6) hex screws securing the rear access panel, then disconnect the (2) power wires from the LED driver module and set the panel aside. Disconnect the 2-pin fan connection...

The lid is modeled in Fusion 360 around the open source model of the Mars 3 to provide a close fit: https://github.com/elegooofficial/Mars3

Just a quick and dirty remix for the Mars 3 Pro. Wanted a place to put my vat. ...Could probably get away with less infill if you feel like it, but only a 3 hour print.

The angle mount that comes with the Mars is adequate but a little fiddly. Hopefully this one serves you better. ... Two part design so layer lines are optimal and can be printed without any supports Uses M3 x 10mm hardware

Ich habe das Original an meinen Mars 3Pro Tank angepasst. Die Tiefe der Aufnahme wurde erweitert (35,5mm) und von der Passform angepasst. ... Zusätzlich habe ich den Halter um 5mm verkürzt, damit das Abtropfen wieder mittig zum Trichter erfolgt.

Designed a stand to hold the Mars 2 Pro resin tank upright at an angle to allow final draining of resin after emptying the bulk of the tank into the resin bottle. The width of the slot at the bottom accommodates a half paper towel folded to soak up...

Place Elegoo Mars on base. It should just sit right in (see first photo) 18. The hose can bend a lot, but don't pinch or kink it! 19. My resin printing corner of the room. ... Here is the fan I bought: https://www.amazon.com/dp/B009OWRMZ6 The speed...

This is a revised version of the platform bracket provided by Elegoo. It helps a lot when removing the model from the build platform because it allows the resin to flow into the tank. Just unscrew the platform from the holder, insert the...

This is a simple DIY Washing Station to be used with the Elegoo Mars mSLA Printer. This will allow the Print Plate to be removed from the printer and placed directly into the Washing Station without having to first remove the print. Everything...

Since I designed this Mars Pro model, its unique resin vat requires a distinct eyetec gauge. I've included files specifically tailored for FDM printers with integrated support systems. ...To prevent resin from getting lodged inside, print at 100% if...

This is my take on a USB Re-locator for the ergo mars, its really simple and easy to print with no supports. ... this part is meant to be installed with a couple of strips of double sided tape, so you can place it anywhere you want in the machine.

This is a revised version of the platform bracket provided by Elegoo. It helps a lot when removing the model from the build platform because it allows the resin to flow into the tank. Just unscrew the platform from the holder, insert the "Platform...

This is a replacement LED Lens Base that "fixes" the gridline issue on the Mars Pro. Simply drop it in and enjoy. Adjusts the focal distance for the lenses and removes some of the weird beam shaping stuff that they added to the original grid that...