thingiverse downloader by 3d models

Sally Brown, from the comic strip Peanuts by Charles Schulz.Sally is the younger sister of the main character Charlie.  She is a kind girl who is creative and sentimental. She shares some of her brother's worst tendencies to procrastinate but is more...

If you are not sure, use a multimeter!Insert the M2.5 nuts the other side and tighten so nice and snugRemove the rear ball plate off the Carpuride unit by undoing the 4 screws. Note that this is a heatsink for the CPU, so take care not to damage...

CTR_eye_a.L and CTR_eye_a.R control the dilation and contraction of pupils by the customized attribute pupil. There are detailed facial controllers. The body has more finer controllers which help create subtle animations. And more... Animations...

Cam interface off by 1.5mm File corrected will have Test 3 Printed in 9 hours. Also adjusted the charging port opening to permit more cables to fit (only about half mine fit). Added 11mm hole on bottom to allow insertion of a 2-way tripod adaptor...

Make perfectly straight inserts with precision using a tip for installing inserts. Learn guide: https://learn.adafruit.com/heat-set-rig/ Project video https://youtu.be/bbsD-3\_AP\_0 3D Hangouts https://youtu.be/AJ9JT\_pHqAw Layer by Layer...

My design - fully encapsulated by the duct and a thin fin at the bottom part of the hot-end (careful, it is just 1.2 mm thin) – unit body is completely isolated and warm air escapes only horizontally. Factory part cooler (radial) is very weak with...

... so the table does not have a lot of structural support for horizontal movement (lateral strength.) It should be fine to hold drinks etc that you would place on a patio side table. Extra strength could be achieved by adding cross bracing if desired.

The reliability of the more sturdy DC15a/s weapons was something that would have been addressed by final production were the project not ultimately scrapped. The X project was ended as a result of a combination of factors: The formation of the...

This project will guide you through the step-by-step to create a Tripod Floor Lamp.It has a lot of steps, but they are not that difficult.List of printed parts:3 feet, 1 for each leg1 core to mount the legs angled1 lamp socket mount1 bumper to...

This is done by creating very thing slits inside the model itself to allow the slicer program of your choice to add additional walls in these areas to add weight to the model. *Note - this design has tight tolerances and is compensated with a 0.15mm...

Please print the tester to check your printers calibration and settings. If the parts appear to be the wrong size, you might need to scale those by a multiplier of 10. General Print settings: 0.2mm layer height 20% infill 3-4 wall line count Part...

***Updated, the correct wings are uploaded*** 7/16, Pjbca fixed a mistake he made by removing both of the mismatched wings from the files and will have the correct matching one uploaded soon. My apologies on that mix-up. Updated 7/7/18, Pjbca...

Edit: I was able to successfully hold a 1kg apparatus with the simplest locking method and by applying a more complex method of locking I was able to hold roughly 2.5 Kg or 5Ib with a force in the downward direction, (I do acknowledge that the...

Polariscope can be used as a handheld device, or stationary by resting the device on the mirror cover. Flashlight recharges via USB, and also features a strobe mode to liven up your user experience. If you want to use a different flashlight, you...

... Print thin walls enabled. No infill. Remove empty first layers, BUT DOUBLE CHECK! Cura likes to put a small "gap" in the first layer for some reason. I fix this by "pushing" the model into the build plate 0.05mm before slicing, see examples.

The sections are held together by "frame pegs". After drilling shaft bushings to 4.3mm, glue the frame pieces together with pegs while using "elbow shafts" to temporarily align sections. There is no really easy way to assemble this Thing. I think...

I did not switch from Betaseron to Extavia by choice. My health care provider, the VA, has been pretty fantastic in recent years at getting me the medications I need. Shortly after I moved from Michigan to Oklahoma, the VA did as it's done with...

Over a century passed by as Uxas endured the worst the Irinaxi could subject him to without outright killing him. He became a training device for new Irinaxi torturers, and an outlet for any who had suffered from a bad day. Always he simply watched...

This suspension is run out onto a sieve to catch the fibres on top and let the water fall through, often assisted by suction. In a paper mill, this process is continuous using a large number of rollers based on the Foudrinier machine. Hand-making of...

They are intended as non-firearm parts for a 37mm flare launcher, with intended payloads being making fireworks using flying fish or crackling fuse, smoke with proper vent holes drilled by the end user, or OC containers. Please observe and follow all...

You can use an actual 6-32 nut if you want, but I wanted something bulkier and easily tighten by hand, so I made the thumb nob.The camers shell section can be separated into 3 parts so you can print the yellow seen in the rendering below.  This...

This was inspired by Gary McCormack's DF64 Input Flow Regulator ( https://grabcad.com/library/df64-input-flow-regulator-1 ) discussed on the Home Barista site. The design has 2 parts: * funnels that operate as an anti-popcorn device. There are...

Normally the protein skimmers have a valve of some sorts that regulates the flow of water outside of the skimmer by the means of restricting the fflow, either wit ha valve taht reduces the area, a riser tube that increases the head pressure...

The back is completely closed and the cable, which has a 2x5 JTAG Header connector, is passed through a hole, which is plugged by a strain relief. To connect the unit to a computer, a cable with 2 USB plugs, and 10-pin header connector on the other...

It's a SCAD file, so it's pretty easy to modify (add/change axis button layout).\nNote: The joystick holes look like they won't be holes, I assure you they will be when they're printed.\nParts:1x Adafruit Feather 32u4 Bluefruit LE1x LiPo Battery1x...

You can import my slicer settings into Cura by going to Preferences > Profiles > Import and choosing the G-code file. Lithophane photo panels Choose a photo and crop it to a perfect square. I did this in Photos on Mac, but it could be done in...

It doesn't have the original piece's latches on the end of each beam, but it still clamps each motor in place good enough (it seems) only by 3 (kinda tight) lips and standoff at the bottom. As for the flight ability of this quadcopter, it doesn't...

It is known that they are governed by Monarchy. </p><p> <strong>Appearance</strong> </p><p> They are very small, gray in color, with a huge head and large, round eyes. Although his head is very large, his body has been very small. </p><p> ...

Resentment mounted when one of Sutherland's factors, Patrick Sellar, was acquitted of murder and then took over one of the massive sheep farms created by the evictions. Condemnation was widespread, and the Highlanders' grievances were heard in the...

As well this does not bolt on in any way and simply is held on by pressure, so it can't be considered a permanently mounted vertical fore grip. 2nd up is Version 5 Super Long as seen printing in Black PLA, designed for optimal comfort and...