thingiverse controller stand 3d models

... to work on some other stuff before doing these last two things. If you run into any issues, please reach out to me! I can be contacted here, but as it's all public here I’d prefer Discord (Tinnut#2956) or a private message over on Thingiverse.

I recommend you use something like this https://www.thingiverse.com/thing:1622868 to check for over/under extrusion. • To assemble: Place the lids in their open position. Align the lowest gear tooth with the bottom gear teeth of the cart Place the...

THIS THING IS BUGGED, AND WILL NOT BE UPDATED, PLEASE VISIT THE NEW UPLOADED ONE HERE: https://www.thingiverse.com/thing:4667329 - INTRODUCTION The Jellybean3D is a fully DIY Open Source 3D printed electric vehicle. Designed to be made with...

The bracket for a Titan Extruder (from e3D) because the one found on Thingiverse places it inside the enclosure, inconvenient and bad for the engine. Which you'll have to do on top of that, because I built without a plan: The vacuum plate for the...

I enclosed an stl file just to get the thing viewable within Thingiverse, but of course it cannot be printed at least due to its size. Please, do not criticize. Another note to the FreeCad file - it is not cleaned up, so a bit messy inside, will...

... the razor blades. This project was instrumental in teaching myself and my kids how to use our new 3D printer, as well as introducing me to Fusion 360. I've downloaded several items from Thingiverse and wanted to contribute something back in return.

This version is operationally derived from my earlier "Reliable Filament Runout Sensor" (https://www.thingiverse.com/thing:2483919) from last year. Both versions are designed to mount on a 2020 bar which can be part of the printer or part of a...

Download this too: https://www.thingiverse.com/thing:3920466 LAST UPDATE: I've removed all the pieces you don't need for the final build, now there are only the pieces you should print (and the bottom section for duplication in metal, and the wire...

The gauge mount as shown in the first image is located here: https://www.thingiverse.com/thing:2991835. The purpose of this thing is to enable users to square their printer's bed to its frame. Auto leveling is helpful, but an auto bed leveler can...

I used Pronterface to send the G-code commands above: * Launch Pronterface * Connect to the printer * File >> Open >> Pick the output_000x.ngc file saved from Inkscape * Click "Print" My First test Plot: https://youtu.be/bNElitMUsGo A nametag for my...

... safer than replacing the original one. You'll probably understand what i mean if you look at the image of my board :-P I use this to reduce the currents for the stepper motors for my C3D-Rom Driver Printer https://www.thingiverse.com/thing:4315542

[based on an idea from dtari https://www.thingiverse.com/thing:2458265). Finally because hearts are a bit fiddly I designed a funnel to refill the hearts, which helps at the setup. In case you do not like the hearts (which can sometimes get stuck, I...

You can use my silicone mixing cup kit if you want: mixing cup pour the silicone into the mold and bump it a bit on the table to release air bubbles scrape excessive silicone from the top, place mold on a level surface and let it cure don't clean...

You could also print your own eyepiece using this project: [The poor mans eyepiece](https://www.thingiverse.com/thing:5889682) ## The focuser tube The focuser tube is the part the let you adjust the distance from the objective to the eyepiece. Print...

To be honest, if you want a benchtop power supply for your hobby electronics projects and you're looking around on Thingiverse I'd recommend you just go and buy a commercial PSU; done and RTG. You don't build one from scratch because you're going to...

The connecting block is still just a rectangle, and it looks like thingiverse's viewer isn't too happy that the double STL file has that connecting block as part of a separate shell overlapping the first plug. Oh, well... it printed fine in Slic3r. ... ...

[here](https://www.thingiverse.com/thing:4662724). This *should* also fit the cinesplore and the fouride if I am not mistaken * Print settings dont really matter. Make sure your first layer is good. * **Vista_Antenna_Mount.stl** * Rear Vista...

No supports are required (although some are recommended) for this design.This was originally uploaded to Thingiverse in 2017, and I have now moved it here as well.I have 15 other Iris boxes designs and I have an instructable describing them and how...

Update 26 Jul 21See this YouTube video by Nils Rasmusson ([https://www.thingiverse.com/nilsynils/designs]) for a performance comparison of this blast gate with other commercially available designs...

I found the design of Klein-laui on thingiverse and tested it… It was fun and worked… for about 5 minutes until the broom adapter snapped clear off the clip…. So I used the quick basic concept of the quick release and added some more stiffness into...

To that end, you may need to modify this Thing by editing the provided `.scad` file and recompiling the `.stl` files using OpenSCAD or the Thingiverse Customizer. You're most likely to want to adjust three variables: * The `buildItAll` variable...

This is an updated version of my Solar Projector https://www.thingiverse.com/thing:6243278 but designed to be lower in cost and requires no cutting of plastic like the original. Once the 3D parts are printed, this viewer can be assembled in very...

Your support is hugely appreciated. Did you know? Some of our designs cannot be found on Thingiverse. If you are looking for more, check out our premium projects:</p> <p><a...

Using the given options, customize the thingiverse model with thickness of 0.3mm, pixel elongation of 1, pixel shape as a square (1), grid size of 0.3mm, border width of 1 mm, and orientation as 1. ...The STL file is created using the provided RGB image...

My main problem with pretty much every setup I'd seen (including the stock one...) was that the spool was always cantilevered off of one side so on both the original holder (which I really didn't like since the spool didn't always spin freely) and a...

I recommend you use something like this https://www.thingiverse.com/thing:1622868 to check for over/under extrusion. • To assemble: Place the lids in their open position. Align the lowest gear tooth with the bottom gear teeth of the cart Place the...

There are several mask models on Thingiverse, but I recently did some character modeling so thought I'd take a stab at it myself. The hockey mask was first as that was easier to manage, and now I've box-modeled Michael Myers. I'll update the...

... <code>soil_box_x2.stl</code> - Holds the 1/5/10 soil tokens. (I printed the tokens designed by Kandyhouse here: https://www.thingiverse.com/thing:5923585) Print two. <code>sprout_box_x2.stl</code> - Holds the sprout tokens. Print two. ...

It fits my particular setup, so check the list below to make sure it works for you!To be able to use my mount you need to have:a mounted bltouch sensor (so you can use the z sensor)the spool holder mounted on the left side of the printer (I used this...

IntroductionThis is a re-programmable 10 character cryptex tube that I originally put on Thingiverse. There are already a few here, but thought I'd bring this one across..</p><p>I made it for a puzzle challenge that I was running. I couldn't find a...