thingaverse benchy 3d models

**The Original 3D Benchy model by CreativeTools.se** **[This is a ReUpload]** [Creative Tools](https://www.creativetools.se/) Creative Tools supplies 3D printer and 3D scanner products incl filaments, accessories and support and also 3D software for...

I only have PLA and PETG right now. I included a picture of the Benchy I printed with the original extruder (left) and the Hemera (right), and a whistle printed with the Hemera. The Benchys are virtually identical, and were printed from the files...

... After I put this on my printer I couldn't resist dialing up the speed and acceleration to stupid speeds and trying to print a Benchy, and I was pretty shocked when something came out in half an hour that actually LOOKED like a benchy. Is it great?

Rule of thumb: VERY small detail like chimney on the benchy, should oscilate around 5mm/s and normal structures are ok to be printed with high level of detail in about 15mm/s. I also turned off the elephant foot compensation, and set the travel speed...

As proof of quality, I can say without a doubt that this dual-duct design is much better; I've printed Benchy after Benchy, and this dual-duct system improved the overhang a lot... For this, you will need: - 1x 4020/10 case fan - 2x 4010 blower...

This should be small enough to not cause issues if a block with one or more plain faces is printed in isolation.\r\n\r\nI found that the type of custom bloks that can be modeled\r\n\r\n //Set default size to 24mm with sockets for the 16mm...

You can grab the Fusion360 “source” file from thingaverse Please keep in mind that I have no formal training on Fusion. <strong>constructive</strong> <em>feedback</em> is welcome!</p> <p>See the photos for the suggested print orientation and...

It will easily outrun a standard hotend, Magnum recommended, If you are going slow in PLA (less than 100mm/s), you may need to run fans at 50%, This is designed for my attempt to do a sub 8 min Benchy. #speedboatrace For V6 body look here :...

Printed items include: * Vibration test - https://www.thingiverse.com/thing:277394 * Cali Cat - https://www.thingiverse.com/thing:1545913 * 3D Benchy - https://www.thingiverse.com/thing:763622 * Spiral Sphere Ornament -...

Possible placement options include above the extruder, on the print bed, or on an adaptor.Monitor the bobblehead for a while to make sure it's REALLY secure.Do not use for printers moving at extremely fast “15 minute benchy” speeds.&nbsp;Can I sell...

It was unveiled during a live stream where Mia, Pokon, and others assembled a giant Benchy 3D print. Ivan saw it, and I never intended to sell this design as is; rather, it was just going to be more of a template. Ivan loved it so much he gave me his...

The Benchies in one of the photos demonstrate the significant improvement in print quality achieved by using this fan duct design compared to printing without cooling or using a different fan duct. The 180-degree version of this fan duct removes any...

It was unveiled a couple of weeks ago during a live stream where Mia, Pokon, and a handful of others assembled a giant Benchy 3D print. Ivan saw it, and was blown away! I never intended to sell this design as is, rather it was just going to be more...

A380: https://www.thingiverse.com/thing:846469 Boat (Benchy): https://www.thingiverse.com/thing:763622 Shark: https://www.thingiverse.com/thing:192007 Whale: https://www.thingiverse.com/thing:2651498 Sea Serpent:...

I am currenting printing 3D Benchies @ only 60% fan speed with sufficient part cooling. The design includes a removable Blade Duct assembly to allow for ease of changing and maintaining nozzles. The assembly is based on a M3 thermal insert and a M3 x...

But if all of this makes no sense to you....I suggest you stop reading now and go back to printing Benchys and Baby Yodas on your stock machine. Now that is out of the way, here is what I did: **FIRMWARE:** I edited the pins_BTT_SKR_V1_4.h file as...

If you're tired of printing mundane objects like 3D-Benchy, the Rothonda offers a refreshing alternative - not only for testing your 3D printer but also as a delightful toy for your daughter or little sister. This versatile model can be printed as...

The 3D benchy printed in blue is with this heat break. Make sure you set the retraction to 3mm. Please note that this only works with ABS. With PLA, you will get jam. For PLA, use the heat break with PTFE. Have not tried PETG yet. ... eSUN PLA Printer...

Print quality is good, and I'll try a benchy and ghosting test later. The diameter of the sticks is 7.2 mm, but sticks with a diameter of 11 mm can also be used - they're almost three times as stiff in theory. 7 mm glue-sticks are fairly cheap, and...

The main pic is 80% scale, and 50% is more like a cute little Benchy sized print. Consider a color swap as it looks way better. Consider changing your top and bottom fill patterns to Octagram Spiral.</p> <p>Depending on your filament, this can be a...

Possible placement options include above the extruder, on the print bed, or on an adaptor.Monitor the bobblehead for a while to make sure it's REALLY secure.Do not use for printers moving at extremely fast “15 minute benchy” speeds.&nbsp;Can I sell...

EDIT 2019-08-17 add images EDIT 2019-08-27 [Test video - benchy on 80mm/s](https://www.youtube.com/watch?v=d9Iq-x4SLc4) EDIT 2019-08-28 publish OpenSCAD sources. ...EDIT 2019-09-01 add dial indicator tool EDIT 2020-04-07 replaced by [HEVO MGN...

Fifthly, I have yet to encounter cooling issues with a 5015 coming in from the side, even on challenging prints like Benchy's bow turned away from the fan. Sixthly, originally this design had a part isolating the heatsink cooling fan from the...

-Multi-material up to three colors with two bowden and one direct drive extruder -Fast(est?) 3D printer self-replication print times Tests done so far: -Direct drive and Bowden Extruders have been tested to make Benchys and work to a good level of...

I am currenting printing 3D Benchies @ only 60% fan speed with sufficient part cooling. The design includes a removable Blade Duct assembly to allow for ease of changing and maintaining nozzles. The assembly is based on a M3 thermal insert and a...

Possible placement options include above the extruder, on the print bed, or on an adaptor.Monitor the bobblehead for a while to make sure it's REALLY secure.Do not use for printers moving at extremely fast “15 minute benchy” speeds.&nbsp;Make your...

**Be sure to check out my other calibration items:** https://www.thingiverse.com/thing:4769286 - Calibration Cube https://www.thingiverse.com/thing:4769155 - Calibration Coin (Test for filament change) https://www.thingiverse.com/thing:4825773 - Full...

I wanted to find a speed where I got peak performance, and the above Benchy is printed at: * 150% scale * Two wall shells * 0.8mm top/bottom * 0.4 nozzle * 0.1 layer height * 45mm/s inner/outer walls and top/bottom * 100mm/s infill and travel * 15%...

Print benchy or similar and use a caliper to measure everything. The type of filament and temperature will affect the fit as well. You can also try stretching the length by a few % to make the fit better for your printer and filament. The SD cards...

**Be sure to check out my other calibration items:** https://www.thingiverse.com/thing:4769286 - Calibration Cube https://www.thingiverse.com/thing:4769155 - Calibration Coin (Test for filament change) https://www.thingiverse.com/thing:4827644 -...