thermoworks probe spool 3d models

I printed my dual-color prints with a single extruder by pausing the printer after the colored backround part had completed and then swapping in a spool of white filament. My printer doesn't support the M600 pause command so I have to pause it...

Initially, I designed a simple 4-nut spinner in translucent red filament (one of my favorite spools). Then, for my wife's and my anniversary, she bought me some FoxSmart bronze filament. The idea of a bronze spinner immediately popped into my head....

It requires a lot of 3 mm bolts from 12 mm up to 20 mm in thread length, (2) 4 mm bolts that are 20 mm long, and (2) 2 mm bolts that are 12 mm long.Assembly Photo Galleries00 Frame System Overview - http://imgur.com/a/nDK1501 Frame -...

I ordered my first spool of flexible filament and can't wait to give it a try. Unless there are any critical feedback points that require additional changes, I'm sticking with this design as is. Enjoy... I know I will too. I've removed the WIP tag...

Frame sides are identical so you can choose left or right for electronics, LCD, potentiometers, and PSU/spools/extruders. The printer is for ten millimeter tr3 trapezoidal rods and this...

Members of my DnD party wanted designs in different colors, but I didn't want to purchase that many full spools of filament. I ended up using a sample pack of 3D pen PLA I found on Amazon. It wasn't the best quality, but it came in a bunch of...

The major change adds a compartment to hold a USB cable and an extra spool of solder. The USB cable compartment is pretty small, though. I only printed it to make sure the USB cable would fit, and it does, but it needs to be coiled compactly. I tried...

Be cautious not to sacrifice too much z-height at the left edge due to material spool spacing. You can rectify this by enlarging the relief box or repositioning it. Optimized specifically for use with 18x24" 5mm (0.220") acrylic available in the...

To use, remove the positive film spool on the left side of the 110A, remove both doors by removing the hinges, and install the grip, pushing the hinge pin through. If the hinge pin doesn't go in, try a thinner wire. Insert the two latch hooks into...

... comment if it doesn't match for you. Print Settings Printer: Prusa i3 China Derivated Rafts: NoSupports: No Resolution: 0.2Infill: 20% Notes: Still using my bad PLA spool that I need to finish, even if I never succeed to get a good print with it.

Allow filament to feed from the printed spool holder on top of the enclosure. Dishwashers typically have a small hole at the top center, which was originally used to mount a spinner and will now serve as your filament feeding point. Employ a...

Each one can have as bottom a tray and here you are, you can dry as much as 5 spools at a time ;)an “hole adapter” to fit the 5mm thich PT100 through the bottom of the dehydrator into the heated chamberI printed it all in black PETG (white would have...

I've taken to throwing the mods on it as I build them, and at some point if they prove reliable, I'll upload most of them here.)\r\n\r\nEdit:\r\nI've now had replacement plates 1 & 2 cut from those patterns and have been able to dismember my printer...

For the smaller sizes which can't be (easily) stripped, strip a double length off the spool then cut the wire and slide the insulation to the center.To bend the wires center the wire in the appropriate slot on the bending tool and bend the legs...

**(update 2017 October 12th: it's okay with an original extruder)** For future designs, I am considering rotating some degrees towards the front the connectors for the chain between the extruder and the X-Motor because as you can see on the...

Filament spool must be mounted below and to the right of the sensor when facing it. Bowden tube mounts to the top of the sensor. In addition to the three printed parts, you will also need: 2x M5 screws - 10 mm 2x M5 t-nuts 2x M3 screws - 18-20 mm...

Parts and quantities you will need to print: 1 x A-top-cap-left.stl 1 x B-top-cap-right.stl 1 x C-left-platform.stl 1 x D-right-platform.stl 1 x E-end-cap-left.stl 1 x F-end-cap-right.stl 2 x G-bottom-cap.stl 2 x H-bottom-cap.stl You will also need...

My other projects Wire bobbin: https://www.thingiverse.com/thing:4946929 Flux Funnel: https://www.thingiverse.com/thing:4946257 Large Spool holder: https://www.thingiverse.com/thing:4816080 TUSH with Linear Bearings:...

It's not visible once fully installed, so I used a spool of PETG that I don't like very much. Even though it happens to be brown-ish, that's just a coincidence. I printed with a 0.4 nozzle and a 0.28 layer height. If you print with the flat top side...

|1| Spool of solder |1| Soldering Iron |3| Rolls of assorted red, black, and green wire|| |1|[5V 15A Power Supply](https://www.amazon.com/gp/product/B08764XJ2M/ref=ox_sc_act_title_1?smid=AOTVD5RNGJU9R&psc=1)|If you choose to use more/less LEDs in...

... I haven't dug into retraction tuning yet, going with 1.5mm at 25mm/s seems to do okay with this new PETG filament I'm using. This was my first spool of PETG and I'm not sure how hard it would be to tune away the stringing the way I could with PLA+.

This formula assumes that you are using standard Makerbot filament that comes in the spools of 900g and costs $48 per roll. If you are using different filament, you may want to adjust the numbers listed. You can easily solve this on a calculator by...

FAQ: https://shivinteger.github.io/about Generating Attributions log: [0] Thing Title: Martian War Machine - War of the Worlds 1953 [0] Thing URL: http://www.thingiverse.com/thing:13159 [0] Thing Author: shivinteger [0] Thing Licence: Creative...

Unlike typical cube robots, this design can be produced at a total cost of $100 across 2 spools of filament and hardware (excluding phones, motors, battery, and Rev Expansion hub). In contrast, a typical robot could cost upwards of $400-$600...

It will soon be time for some neat tidying up and installing the remaining lower shelves that display my completed 3D prints alongside those filament spools, all the while keeping in mind how well the existing setup blends in with other things in The...

Done.Updated on 2015-01-18- I've reworked the Z axis end stopper, and it looks better now.- I plan to unsolder the Full Graphic LCD controller, which will allow for better integration of the screen and controls into the design.- Some minor rework has...

the paracord spool has a tensioner on the bottom of it, see the remix i tagged for pictures on how this works. I didnt actually remix his model per se, but i did basically copy it in my design. (thanks mikeaj) This has 550 paracord strung through...

Also made a 3 spool holder right above the extruders. Next step now is uploading the software. Software: I'm realizing this hasn't really been done...so if anyone has feedback to get dual Y-bowden setup properly, let me know. I have an AIO that had...

I threw my spool of poly-carbonate into the toaster oven and got to work.I broke out Fusion 360 and whipped up a quick design based on the measurements. <img...

The width of the border and the separating line are 0.8mm so at default scale it's well-suited for printing with a 0.4 mm nozzle using a 0.4 mm extruder width. I printed mine with a single extruder by pausing the printer after the black part had...