thermaltake core p3 parts 3d models

This is a Adapter Plate for mounting a "AquaComputer Ultitube" in a Thermaltake Core P3 Case. The size of the reservoir (100/150/200) does not matter, because the mounting is the same. In this Version i have no holes. i drilled them myself after...

This upgrade builds upon the core of the NCS P3-v Steel printer, utilizing most existing hardware. To take advantage of this upgrade, the NCS P3-v Steel printer must be either purchased or already owned. This upgrade will not work with the NCS P3-v...

Thank you to those who purchased the NCS P3-v Steel keeping to the core of the NCS P3-v Steel printer this upgrade uses most of the existing hardware This upgrade Requires the NCS P3-v Steel printer to be purchased or already owned This Upgrade will...

This is an adapter plate I made for the Thermaltake P3 case so I could use a Swiftech pump. It also adds a USB C via a motherboard connection. I used this cable from Amazon:...

This is a Block you can add to the Core P3 Case to mount Acrylic panels to mimic a Smaller Core P5 Case. ... It has the proper holes for a Brass M3 Insert commonly found on Amazon, use with a M3 Thumbscrew Use a solidering iron to slowly press fit the...

Individuals often utilize a standard SSD holder, however I opted for the Thermal Take Core P3 instead. ...Since I do not rely on a watercooler, this unique holder can be employed anywhere, serving as a convenient storage space for older SSD drives such...

I have the case mounted to the wall behind and above my monitor, so this cabling is at eye level…When browsing, I found Thermaltake Core P3 Psu Cable Cover by Bl4ck, but the PSU in the  Core P3 chassis is rotated 90°. That's why I started designing...

Case feet for Thermaltake Core V21 to fit into my kallax in my front room

This project is for inserting a mayflash 4-port Gamecube adapter into a Thermaltake Core V1 case in the GPU hole of the front panel. ...WARNING: This reduces the potential of using larger GPUs.

This is a custom-made logo replacement for the Thermaltake Core V21 Case, specifically designed to upgrade its aesthetics. Two variations of this model are available: a solid plate and a version featuring a screw hole. ...I opted for the latter,...

The Thermaltake Core P1 comes with a single hard drive holder, which wasn't enough for my needs, so I created this attachment to add two more. ...This design mounts the additional hard drives on the exterior of the case, elevating them above the upper...

Purchased a Thermal Take Core W200 case, only to find it lacked sufficient L Brackets for installing all available accessories; I therefore designed these brackets to enable users to install accessories such as the MAX 3504, MAX 3503, or MAX 2506,...

This is a replacement for the logo plate that goes on the front of a Thermaltake Core V21 Cube PC Case. The original has a 10mm x 2mm magnet already inserted, I didn't include this hole as I was going to drill one into it manually. ...It's blank so that...

This is a remix of the Thermaltake Core P5 X-Flow 480mm Radiator Bracket by VanGoghComplex.https://www.thingiverse.com/thing:3319813 I made it 10mm wider to fit my Black Ice X Flow Radiator. I also modified it so you can print it flat with no...

This is a quick mount I designed to mount the pump / resevoir of the EKWB fluid gaming set more to the top in my Thermaltake Core P5 case. The Mount uses only hardware that is included with the fluid gaming set and is pused into a hole in the case.

This is a rapid mount I created to elevate the pump/reservoir of the EKWB fluid gaming system higher up in my Thermaltake Core P5 case.\r\n\r\nThe Mount relies solely on hardware provided with the fluid gaming set and is secured into a hole in the...

This is a quick mount I designed to mount the pump / resevoir of the EKWB fluid gaming set more to the top in my Thermaltake Core P5 case. The Mount uses only hardware that is included with the fluid gaming set and is pused into a hole in the case.

Today I bring you a brand new version of my Thermaltake Core P5 radiator bracket. This one is specifically designed to allow you to install a cross-flow 480mm radiator between two of the corner posts on your Core P5 open frame chassis. I am not...

PCI-E riser cable holder for Thermatake Core G3 case. ... For single height card.

Despite its design limitations, it's surprisingly easy to fit an mATX board into the Termaltake Core P1 case - just be prepared for the fact that it'll be secured by only four screws. To accommodate a graphics or extension card in one of the lower...

I have a Thermaltake Core P1 case and since it is an open case there is no option to cool VRM zone and SSD radiator on my motherboard with watercooling. ...So i made this simple two part solution that is mounted on the upper left bar only and can fit...

No description provided.

I am a Text Rewriting Bot. I will rewrite the given text to match its original tone and voice while using active voice throughout. The rewritten text must score 100% on the Flesch-Kincaid test. I will avoid any expressions like 'Here is the spun...

This carriage is designed specifically for this thing: https://www.thingiverse.com/thing:2849015 I have plans to design some other V2 parts as well. https://youtu.be/6INCqltFkIg Added new hotend clamps. 20/0319 Added new carriage with clamp in...

p3

It was designed for INAX Bath . ... Catching hair as their parts PBF-5H-C4. So far designed according to INAX document as replacement own parts.

... Available. ... The essential components required for modifications are listed below. The remaining parts, however, remain unchanged and can be sourced from the main page at: https://www.thingiverse.com/thing:2849015 https://youtu.be/9vhQ82_5Gbc

Here are the parts you need for a 25mm frame material, specifically the ones that require adjustment. ...Everything else is still the same as on the main page and can be found at: https://www.thingiverse.com/thing:2849015 or watch this video at...

This design was created with my existing design tool head parts in mind, which are available below: https://www.thingiverse.com/thing:2576080 The Z Axis components I designed can be found here: https://www.thingiverse.com/thing:2861738 I built this...

This bracket will mount a 360mm radiator to the top of a Core P3 using 2020 extrusions for posts. Tested with Kraken Z73, but should fit any 360mm radiator. ...I used #6-32x3/8" screws to attach the radiator to the brackets, and M4x35mm screws and...