the ulti 3d models

The Ulti-Bot is 126mm wide, 104mm deep, and 155mm tall, made up of 37 assembled parts (excluding the figure and spring). It's printed in a combination of flexible black, silver, and yellow Ultimaker PLA. Most parts snap together; careful assembly is...

Check out the competition results at http://grabcad.com/challenges/ultimaker-3d-printer-toy-design-challenge/results See the robot in action: https://vimeo.com/67641975 We set out to push the limits of what's possible with the Ultimaker 3D printer,...

Blowing out details of the Ulti for coolers 3010.

You've got a dilemma - placing a sticker on either your Ultimaker 2 or the Ulti-BASE. The problem is that both are brand new and untouched. ...So, draw inspiration from the sticker to create a custom plate that not only holds its place but also features...

The Ulti-BoBot, a childhood dream turned reality, was created as an articulated 3D toy during a design competition. Inspired by Octonauts cartoons, the robot tank was designed to collect objects and store them in its rear hatch before expelling them....

Customized Version of a Thing from the Thingiverse Website Created with Customizer Tool on Thingiverse Website Instructions Using the Options Listed Below number_of_planets = 3 width = 5.5 inches planet_pitch = 45 degrees tooth_thickness = 15 inches...

Airflow models for the Hotend E3D Volcano to the Ulti Printer.

The owner of the camera attached to the Ulti case uses a standard GoPro screw for mounting. ...Additionally, a versatile universal screw mount found at http://got.by/2v6bnc can be employed.

Plugs for the Ulti Steel body: * SD card if installed [Case lcd 12864 UlTi Steel 1.0](https://www.thingiverse.com/thing:4156868) * Angled top holes * Holes for XY motor pulleys Donate with Yandex Money https://money.yandex.ru/to/410011193970761...

The UlTi doesn't need improvement, but small modifications won't ruin it. 1. Telescopic spring guides - to stabilize the bed springs. 2. Spool holder pad - to prevent jamming of the spool. UlTi не нуждается в улучшении, но маленькие модификации...

In comparison to the standard Ulti-Foot, this version boasts a height of 14mm. Please follow these instructions for printing: 1. Print two copies each of 'ulti-foot.stl' and 'ulti-foot-mirrored.stl' from the original design. 2. Additionally, print...

EN I didn't like the spool holder on the UlTi Steel from the very beginning. It is simple, cheap and technologically advanced in production, but the spool with plastic on it rolls over and makes unpleasant sounds when printed. When printing TPU,...

Ulti

Motor shaft rotation direction indicators are essential for the ULTi Steel 3D printer with conical shaft fit. ...To print these indicators, simply use the existing design for Y motors and mirror it in your slicer for extruder and X motors.

This is an extension for the Ulti Steel top cover (see remix) - the holder for T-125 Carbon filter. There are two ways to print Filter Holder part: with supports or without, but gluing will be needed. ...

Ultimaker and Replicator noise dampening feet require printing 2x 'ulti-foot' and 2x 'ulti-foot-mirrored', along with 4x 'ulti-toe'. ...To install, cut 8mm x 1mm rubber bands (62mm long) and follow the photo's instructions.

Ulti-Flat X Carriage & SDP Bearing Mounts - An Improved Version of Supa-Flat Carriage The Ulti-Flat X Carriage boasts slots designed specifically for SDP bearing flange placement, preventing the bearing from slipping out and reducing binding. This...

... of noise-dampening feet for Ultimaker and Replicator. ...Instructions: Print 2 Ulti-foot units, 2 mirrored Ulti-foot units, and 4 Ulti-toe units. Cut rubber bands measuring 8mm x 1mm in length, totaling 62mm long. ...Insert them as shown on the photo.

Information Model designed for securing the RS10TV socket interface in the top part of the Ulti Steel printer casing. This concept allows swapping the printer head completely, without needing to mess with the wiring. ... #### List of components: * 4x...

You can use the original parts UlTi v1.2.6, https://www.thingiverse.com/thing:2246310 Compatibility with the original printer is fully preserved. A tensioner for the Z-axis belt is used, taken from the Y-axis belt CR-10,...

First of all, it was designed specifically for installation on the ULTI Steel case of the first revisions (with mounts for lcd 2004), later a universal version was released. For new cases originally coming with 12864, print "angle case lcd12864...

... incorporated thicker support structures that can be easily removed after printing. The user is free to scale up the ring as desired, with a caveat: if the scaling factor exceeds 20 times the original size, the support will automatically disappear.

... out accessories such as swords, shields or other attachments. ...The innovative jointer component ensures seamless connection between the robot's body and appendages, while left and right arm options and a versatile cannon arm enhance functionality.

The ultimate upgrade for your Replicator printer features an expansive 16x16x16 inch build area and was exhibited at the World Maker Faire NYC 2013. This design is still a work in progress, utilizing extruders and Mightyboard electronics from the...

http://www.thingiverse.com/apps/customizer/run?thing_id=1043468 Instructions Using the following settings: Height = 40 Width = 8 Length = 180 Layer Delta = 0.1 Inner Wall Height = 1.5 Outer Wall Layers = 5 Corner Roundness = 2 Number of Facets = 100...

... Instructions Using the options: Wall width: set to maximum (1). Spiral width dimension set to 7 units. Ribbons count specified as 13. Model type selected is Type 1, a classic variant. ...Diameter measurement stands at an impressive 45 units.

Information The model is designed for attaching the plug-socket assembly (based on RS10TV) to the back of the protective cover for the Ulti Steel 3D printer (also possible without a mounted protective cover). Using this concept allows you to swap the...

Ulti One Piece