thangs 3d printing

Access it here: [http://www.thingiverse.com/apps/customizer/run?thing_id=287025](http://www.thingiverse.com/apps/customizer/run?thing_id=287025) To print this design, set the following options: - grid size: 0.1 - orientation: 1 - pixel shape: 4 -...

I had problems with the walls printed vertically. As the plastic wires are laid one on top of the other, the wall is not very strong and it had the tendency with thermal shrinkage to crack. So I added different shaped ribs to see which ones are...

all parts: layer height 0,2mm infill 10% to avoid an elephant's foot and thus to achieve an optimal fitting width, you can also print the plates with raft. a maximum of 100 pieces are needed. you can clip them by hand into the holders of the frame...

For the actual printed parts, this is designed for the tolerances I have experienced with hole shrinkage. It is intended to be relatively tight to the shaft so gently clean out the hole and push onto the shaft. It may take a couple of times to get...

(STL included for the feet: print four of them in TPU for best handling of vibrations) * Low version, which does not require feet to lift the Ender 3 Pro. There is no slot for a fan however. Use at your own risk as my advice is to always use active...

You'll find the clips as single objects or as a complete set to download and print. Changelog: The clips now hold LM8UU bearings more tightly Bearings are pressed against the Y frame to prevent them from spinning. M3 screw holes are narrower now,...

You'll want to print two each of the bottom stops with and without dowel, and as many of the top stops as you care to use to mark your positions. To finish/calibrate the stops, do the following: 1. Glue/epoxy 1/4" dowels into the holes. These...

There will be a lot of soldering, and you'll want to make changes to the CAD and do a few test prints of your own if you want good results. Read further down for more info. === Flaws === Firstly, you should know what you're getting into. To be...

(perimeters may be reduced to 3)100%Ø50 /Ø60 Ø3,7M4As printed (set perimeters to 4)125%Ø62.5/Ø75 Ø4,6M5(set perimeters to 4)150%Ø75/Ø90 Ø5,6M6Advisable to use a tap! ...(set perimeters to...

So I created and printed some using CAD. I screw all the holes in the MGN 7. It is required for the MGN 7 M2 screws. If you get a longer rail you can use the other belt tensioner in the mod. This is stable enough. The assembly ... Then the...

Then generate and print one using this bearing generator. I've use it to generate slide and ball bearings for EMT electrical pipe and 8mm rod. There are lots of parameters with defaults for most settings. This design requires omdl.The ball bearing...

It should be fully rules complaint but check dimensions before using this design.Note: At time of upload, the design has not been tested in competition and has no guarantee of performance.Note: The pictures included with this design show a Launcher...

... Curved step dr. x 6 * Straight step x 12 * Pot x 1 The file of the cards is mounted in six units with two spares in case some are lost - this way, they can be repositioned with matching color. There's also an individual file for printing as needed.

Print all the parts before assembling anything. 4. Start by assembling all the windows, doors, and trim as shown in image 1. 5. Assemble the motor mounts by gluing the two halves together. Ensure you align the holes before gluing. 6. Attach them...

Presupported and Test Printed!   Ironside soldiers are a type of android designed to function as soldiers or enforcers. They are humanoid in shape, with a durable metal exterior that gives them an intimidating appearance. They are equipped with...

---------- PRECAUTION: Après quelques prints, il faudra contrôler que les tensions soit toujours bonnes. Procéder à un ajustement ci nécessaire. ---------- Ce custom est un projet personnel, qui m'a pris beaucoup de temps à concevoir et à...

The assembly takes about half an hour.Designed with Autodesk Fusion 360All parts are designed to be printed without material supports ### Parts to be printed - The main body (choose the model corresponding to your hotend : E3Dv6 or XCR-BP6) - The...

I provide an easy-to-print alignment tool to ensure the heatsink is perfectly positioned for the cover to fit.\n* Direct airflow through the heatsink, don't leave proper airflow to chance.\n* Duct air in one side and out the opposite to maximize the...

2) when everything are ready, and the housing was printed out. you can starting to connect the circuitry as per attached diagram. Please make sure the coinnection is correct before you put through the live electric supply. 3) I didn't reserved the...

I printed the part using supports which are only necessary for the corners to the upright face. -- x -- I've also included a camera housing for the rear camera (plus fittings). It is intended that this will be attached to the upper plastic trim...

Ideal material: alveolar plastic thickness ~ 2mm (from supermarket advertising panels) Flexible plastic mesh 5x5mm: cut-out size 430 x 220 mm Diameter of the holes: Passage Bees + Hornets: Ø8 to 9 mm Passage Bees only: Ø5 to 6 mm Print the 3...

(For a 6x12 building, for example.) Note that the roof will take a lot of materials to print, but if you like the style, go for it! EDIT: Check out my new Ultimate Roof Building Kit to further enhance your Roof building options, supporting various...

The transformer comes in 2 Variants and you could either print it complete or in parts however you want to. ... ________________________ <b>If you like my work please consider supporting me on Patreon.</b> <a...

A constant current driver operating from 6 V to 15 V should do nicely for powering it directly from the main battery and adding an RC switch to control the light by the transmitter.\r\n\r\nI printed the chassis without supports using PETG and lots of...

----------------------------------- What you will need: * Four of the Corner Posts printed in your choice of plastic. * Two strips of polycarbonate strip 1/8" thick, 4" wide, 2 feet long. (Available from McMaster Carr in the USA part number...

The secondary goal was to keep it simple and quick to print.The tripod consists of the following components:Tripod Head: Featuring fixed holes positioned at 20 degrees from the central axis.Telescopic Legs: Made from 6mm outer diameter and 4mm inner...

This design fits on a Prusa i3 MK3 bed.Note: Please only attempt this if you already have some experience with soldering, wiring and electronics in general.Note: Some ATX PSU's may be too deep for this design so if your PSU is over 135mm deep it may...

I made some different designs and prints to hold the start of the wire in the chuck. My thoughts were good, but using them didn't bring the solution. Then I came up with the idea of making a kind of vice that could be placed into the chuck and clamp...

We merely tighten the hard plastic filter mounting hub against the printed (hard) top rim of the porkchop's stem. This appears to be good enough for me, but you should test it and add a seal if necessary. A flat O-ring with an ID of 22 or 23mm...

You don't need to print anything to get it working. Another thing I noticed, If you extrude filament on the button and then press again to stop. The hotend does not switch off on this printer. Kids fire hazard if left on Of course if you went...