thangs 3d model

The STEP file is included for easy remixing. Please post any makes and if you see a problem please post a comment. Updates: 4-30-2020: Thanks to feedback, I corrected the model for the base, the updated version is "6I". ...None of the other parts...

I have not modeled any nut traps in the parts because I think they will weaken them so all bolts here just screw into the plastic. I believe the parts are thick enough that the bolts will not loosen but time will tell._ 1. Completely disassemble...

 I have it installed on both my printers and it's really nize.MK3S and (+) versions of the adapter are unique to each model and not interchangeable.Both adapters drop in over the screw heads as shown and get trapped between the extruder body and...

Printing Recommended slicer settings: Resolution: 0.1mm - 0.2mm Infill: 10% - 20% Supports: Doesn't Matter Rafts: Doesn't Matter License The "Customizable Arduino Nano LED Candle (2 - 6 LEDs)" model (.stl) is licensed under the CC BY license by Code...

The retainer is up higher than need be in the video for safety.--------------------------------------------------------------------------------------------------------------All parts printed in PETG, with standard Voron settings for rigidity.0.20...

There seem to be quite some error margin in production, if your model is a bit too big to fit, just sand off maybe .5 mm from the sides to make it fit.Completely(!) remove any filament remains inside the two enclosure parts.Fit servo into upper half...

If you have a tuned in printer, bump the speeds up a little for a dramatic improvement, (make sure wall thickness is a multiplier of your nozzle thickness - The parameters are important and there are a lot of dependencies, Make sure you have done the...

Update 220811:Added solid with 1deg step on requestReplace the code below to this, (BB and CC changed to 2 and 1 and replace STL to the new...

You can find a somewhat more detailed list of supplies in my Instructable at https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Basically any combination will do (as long as the driver is 3.3" or smaller so it fits the...

If you want to use the hardware I intended this to use: Hinges Bolts- https://www.mcmaster.com/91292A018/ (you will need to thread inner most hinge) Hinge spacer- https://www.mcmaster.com/91755A311/ (you can see in the photos a little bit of white in...

Deck furniture is always a good way to add interest to a model. You might want to install a waterproof switch somewhere on the exterior to save having to unscrew the whole deck every time to turn it off and on. Enjoy sailing your Pocket Boat,...

they are built into the models. Use the provided M2.5x10mm self tapping screws by default unless told otherwise. As an alternative to jig cutting, a drawing for manual hole drilling is also provided. In addition you will need: - Hot glue...

Downloaded some Radio Control model yacht designs. Non of them suited my fancy for building, so I decided to come up with my own. Main Desing principles... No Keel! -> Surf Board / Windsurfer style. Light Weight (relative to size of jib!) ...

Remember to check the wiring of your relay if you use a different model or brand. Adjustments If you set the microswitch to click when the bed is at Y=220, then it will work out of the box with Cura. I still recommend you to modify you G-code to...

*Download new version 1.01 here: https://www.printables.com/model/178925-ender-3-s1-stealth-light-bar-easy-to-print-and-do-mod ( Maintaining on Printables ) Easy to print light bar that uses the built in accessory port for power. This allows for...

4028 fan mount: Note this is modelled with internal supports in the top section of the duct to make it easier to print. Please remove these supports after printing. 4 x M3 32 mm (upper fan mount) 2 x M3 x 12 mm cap screws (lower fan mount) 6 x M3...

(In the future, I'll model a printable screw-gun interface for people who can't get the part in question.) 4.#6-32 brass nut, 1/4" across (measured face to face), 3/32" thick (optional) McMaster-Carr 95130A120. Fits into a pocket on the gun carriage,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

I have completed the task, which is an intricate and comprehensive model. It required two full weeks of my time. I eagerly anticipate your appreciation for it; have a great day! :) :)</s> щ поставих задачата, която е детайлна и обширна конструкция. Я...

Make it Free the figurine from the Lunochod modell. See the picture. Drill / cut through four tabs (red circles). Two starts are hidden (see the residues after cutting - the blue circles). . The Sandmann figurine has a metal tab with threaded...

Basic overview:This is a drop in replacement barrel for the Dart Zone Solo Pro that is designed to allow it to fire mega darts, but I designed the model in a way that it can not only also still fire half darts, but fire rival ammo too! It shoots Mega...

Cable clamps bolt to the Extruder mount bolts to keep the cabling tidy, which I've not used yet as I can currently only run 1 of the heaters at present (my A20M control board is a V4.1 model which doesnt have the components fitted to allow for dual...

You may need to adjust your printer, sand the chamber a little, or apply some force, as the parts were modeled to fit with ZERO clearance, to assure the best possible bond when using superglue. Just apply superglue to the syringe holder anywhere...

Update 2021/02/06: Upgraded parts- steering arm 2.0 Bump steer reduce for steering knuckle 2.0(the ackermann angle have been reduce on steering knuckle 2.0 and therefore with the change of geometry this part is required to reduce bump steer) Update...

If you don't want to mess with a PLA support, you could probably print this part in two separate objects.I provide you the Fusion 360 file, so you can customize and change the model according to your rail system. I strongly recommend you to...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

Just go on Amazon or Ebay and get a metal vice and then bolt it down securely on your workbench.The specs for this little guy are:40mm jaw opening20mm jaw widththroat depth 12mmThanks to a metal screw (M6x60) and an M6 metal nut as inlay, it is...

head), I recommend staying in a 18-25 mm range for the thread length, to give yourself some margin.For my US friends using imperial, you can use #4 screws but you will need to adjust the nut parameter in the f3d file.Also, I think it doesn't leave...

If your name is not Matt, then there is a template attached in the model files called “Name_Plate_Template”. If you wish to add your own name to this template, open the attached file called <code>Name_Plate_Template.step</code> in a CAD software of...

To connect this to the second hand holder disc, I bought a plastic tube of 1mm inner diameter from a modeling shop. I pinched one side a bit to make it flatter. This seems to work, but maybe I will have to glue it on the pin. I didn't do so yet...