th d74 case 3d models
214304 3d models found related to th d74 case.
thingiverse
A cup/thing that mounts to a flat vertical surface that I can drop my TH-D74A into without worrying about dropping it on the concrete floor below (if not for that, I'd just use an old belt). Front loop for clipping a speaker-mic onto. OpenSCAD...
thingiverse
It's a pretty expensive radio that I didn't want getting dinged up, so I bought a soft case/cover for it. Unfortunately, with the cover in place, the radio does not stand up on it's own such that the antenna is properly oriented, so I designed this...
thingiverse
Bought a Kenwood TH-D74A, and decided I needed a Desk Stand for it.
thingiverse
From Randy - W4LKS May 2020 Kenwood TH-D74 3D Printed Desktop Stand Here is a simple desktop stand that holds the '74 at a pleasant angle for viewing the screen while it sits on your desk. The base is wide enough so it would be hard to knock it over....
thingiverse
https://www.tinkercad.com/things/4WyS8fxde3D new: TH-D74 Halter_2.stl thinner Version. new: TH-D74 Halter 3.stl . ...Modified for new 4 Quick-FIX HR-Adapter.
thingiverse
TH-D74 is a really cool radio, but it's a bit of a battery hog. If you're going out for more than a few hours you might want a spare battery with you. This is a cover to protect the internal terminals. It also have an indicator switch you can...
thingiverse
September 2020 From: Randy - W4LKS Holder for Kenwood TH-D74 handheld ham radio designed to attach to a RAM mount to allow mounting on handlebars, dashboard, windshield, etc. Requires a RAM diamond base like this one: ...
prusaprinters
TH-D74 is a really cool radio, but it's a bit of a battery hog. If you're going out for more than a few hours you might want a spare battery with you. This is a cover to protect the internal terminals. It also have an indicator switch you can toggle...
thingiverse
I designed these 3 cases to be printed with TPU Filament. One has Kenwood logo and one without and one more simplified. They are a work in progress. You can cut the horizontal side supports out of the right side SD/Charge/Mic port opening after...
thingiverse
I wanted a decent stand / holder for my Kenwood TH-D74 Radio when I use it in the house, or a better more secure way of holding it in my car. So I designed this stand and after several iterations, settled on this version. Features include: -...
thingiverse
This is a 3D printed case for the Kenwood TH-D74A ham radio. I printed this in TPU material and it fits well. You can access all the controls on the front and sides of the radio and the back clip holds the case in place. The flat bottom allows the...
thingiverse
This is a case i designed for the TH Custom Signal Tracer Pen. ... https://diy.thcustom.com/shop/signal-tracer-injector-pen-v6-2/
thingiverse
Designed up this to be able to use two 18650 batteries with my Kenwood TH-F7. Need wiring and if you want to charge on board need battery protection circuit. ... Version 2
thingiverse
Customized version of https://www.thingiverse.com/thing:3516901 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3516901
thingiverse
Customized version of https://www.thingiverse.com/thing:3516901 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3516901
thingiverse
Customized version of https://www.thingiverse.com/thing:3516901 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3516901
thingiverse
Customized version of https://www.thingiverse.com/thing:2866563 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2866563
thingiverse
Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130
thingiverse
Customized version of https://www.thingiverse.com/thing:714444 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=714444
thingiverse
Customized version of https://www.thingiverse.com/thing:739573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/9klrZLIOjsi Model of Sonoff-TH ESP8266-based power relay board.