test cube 25x25 3d models
263013 3d models found related to test cube 25x25.
thingiverse
Test for mmu2 or any color printer, a simple test cube in five colors. Cube dimensions: 20mm x 20mm. Color assignments: Color 1 is represented by the letter "x". Color 2 is represented by the letter "y". Color 3 is represented by the letter "z"....
thingiverse
... exactly 10 millimeters by 10 millimeters by 10 millimeters. ...The test consists of five rigorous evaluations: the Bridge Test, a challenging 45-degree assessment, the Tunnel Test, a vertical round evaluation, and a horizontal round examination.
thingiverse
I created a cube to test various printing scenarios, including retractions, bridging, and acceleration techniques on curved surfaces. The structural frame measures 20x20 millimeters. ...Give it a shot!
thingiverse
... this will be a single wall print. You can measure the wall width and adjust your flow accordingly. I saw people were trying to do this test by taking full cubes and making them hollow on Cura settings. This saves you the trouble. Enjoy! ...:)
thingiverse
With the benchy cube, you can thoroughly test all aspects of your 3D printer, including ghosting, bridging, circle overhangs, and 45, 50, and 55-degree overhangs. You can also fine-tune your retraction settings and precision, both for the first layer...
thingiverse
This is a simple display stand designed specifically for the innovative Test Cube by UCS1, crafted to securely hold the cube in place on a corner. I intentionally made it slightly larger to accommodate weight, as my own lack of attention during...
thingiverse
I'm not even sure it's a perfect cube, lol.\nBut anyway, this thing will put your printer to test, so make sure to watch the print so it doesn't fail!\nEDIT: 10-28: Added dual-extruder version. I don't have dual-extruder printer, so if there's...
thingiverse
This is a precise 20mm cube test piece designed for printer calibration, featuring a precise 5mm center square cutout to verify accuracy. ... Print Settings: Printer: MadCat MKII Rafts: None Required Supports: Not Needed Resolution: High at .4 mm...
thingiverse
Both versions available here: https://www.prusaprinters.org/prints/20588-kobayashi-fidget-infinity-cube-torture-test-mmu2s- This was inspired by https://www.thingiverse.com/thing:1923755 Although redesigned from the ground up. This has a nice hand...
prusaprinters
But should print fine without supports. Layer hight 0.1 or 0.2 mm Cubes printed with 15% infill and the hinges with 100% infill Take note: just after printing you need to break the hinges loose from the cubes - this takes some effort and could...
prusaprinters
The super lattice cube is two lattice cubes rotated in on each other, and it makes everything look quite complicated. The Ultra is three, and the unsymmetric is two cubes, but not rotated in a way that makes them symmetric. That one was an accident,...
prusaprinters
Maybe if it was split in the middle and then glued together, it could work without supports, but you'd need some seriously good bed adhesion to do that. EDIT: 7-19-17: Added no-base versions of all of the other lattice cubes, except the dual-extruder...
thingiverse
A 32mm cube features a flat test hole measuring 19.55mm by 3.55mm and a rod test hole of 9.65mm. The materials for the Rod/Flat are sourced from Home Depot; specifically, an aluminum round rod with dimensions of 3/8" x 4' (Part #142-820) and an...
thingiverse
The OpenSCAD file for this cube is also included, as well as a smaller 1cm version featuring a 5mm hole, perfect for printing at 0.1 layers. This test print takes approximately 10 minutes to complete and is ideal for rapid iterations. Once your...
thingiverse
I support Motor Z with a profile that has 25x25 mm grooves and an M5 thread.
thingiverse
20x20 To 25x25 Whoop Mount Adapter. ...One is centered and one is offset.
thingiverse
modified from other hex grid. ...has edges. original only went to 10x10, this goes to 25x25
prusaprinters
to adapt easily your VTX walksnail 25x25 to a 30x30 stack Category: R/C Vehicles
thingiverse
to adapt easily your VTX walksnail 25x25 to a 30x30 stack
thingiverse
Single wall box test cube to be used to calibrate flow rate for CR-30 print mill or other print mills. Printing: Layer height: whatever you are targeting Shell count: 1 Top layers: 0 Infill: 0 These settings will print it with a...
thingiverse
To ensure precise measurements, I am checking the dimensions of a 20mm test cube. This design includes a 10mm round hole and a matching 10mm round peg, which should fit perfectly together. After printing with Simplify3D's horizontal size compensation...
cults3d
Inspired by Oriental woodwork, this model demonstrates the "impossible" object trapped in a cube. ...The floating sphere and intricate details of the cube were only made possible by the water-soluble support material used in the printing process.
thingiverse
These are 3 calibration cubes for seeing if the printer prints the actual dimensions drawn in a 3-D program. ...The cubes are 10mm, 20mm and 30mm wide, deep and tall so respectively 1000mm³, 8000mm³ and 27000mm³.
thingiverse
... are available: 2 parts or 4 parts. You can find a reusable 100mm cube design here: https://www.thingiverse.com/thing:3206211 (no multi-material). ... Unfortunately, I don't have access to the original cube design and its source is no longer known.
thingiverse
I created a 20mm test cube nearly a year ago for personal use, and since then I have fine-tuned it by cutting circle and square holes through it to give me several tests in one: 1. XYZ calibration - the 20mm on each side is precise. 2. Hair test -...
thingiverse
This small solid cube features a spherical void inside it, making it perfect for testing optimal print settings on FDM printers before attempting more complex projects like Cymon's Skull Dice. I've also included a model with small drain holes for...