tesla model 3 frunk
2469405 3d models found related to tesla model 3 frunk.
prusaprinters
This is an insert to level the floor of the Tesla Model 3 frunk so it can be used for pizza/carry out without the toppings sliding to one side. Print instructionsPETG or ABS recommended to better handle outdoor temperatures unless you live somewhere...
thingiverse
Craft a custom cover to dig out a more spacious recessed hole for the Tesla Model 3's frunk release button. This thoughtful move will prevent accidental triggering of the button by shifting items in the frunk. ... The shroud surrounding the frunk latch...
thingiverse
If you own a MY2020 Tesla Model 3, you're probably aware that they don't come equipped with frunk shopping bag hooks. Now, you can easily create your own. The necessary pieces can be printed without support material, but I find that printing with...
thingiverse
The new 2020 Tesla Model 3s no longer come with frunk hooks, also known as grocery hooks. A helpful individual on reddit, redditor_8675309, scanned these hooks so others without them can 3D print their own versions. Feel free to remix and improve...
thingiverse
These Tesla Model 3 Front Trunk Hooks for grocery bags are designed specifically for newer Model 3's that no longer come equipped with the original frunk hooks. To install these, you'll need a 10mm wrench to remove the existing bolt. Once removed,...
thingiverse
This part reinforces or repairs the Tesla Model 3 front trunk (Frunk) supports at the rear edge of the frunk which are prone to breaking when the cabin air intake grille is installed. The Tesla part being reinforced or repaired is 1131205-00-C. By...
thingiverse
Logo MODEL 3 to stick on the FRUNK Double-sided tape transparent to stick on the frunk size : 93.47mm x 11.72mm x 15 mm
thingiverse
To avoid smaller items rolling around in my Tesla Model 3 (2021) frunk, I was interested in a secure post or two that I could attach items to. The Model 3 has two adjacent bolt wells in the frunk that can double as securing points. NOTE: Earlier...
grabcad
To avoid smaller items rolling around in my Tesla Model 3 (2021) frunk, I was interested in a secure post or two that I could attach items to. The Model 3 has two adjacent bolt wells in the frunk that can double as securing points.NOTE:Earlier Tesla...
grabcad
To avoid smaller items rolling around in my Tesla Model 3 (2021) frunk, I was interested in a secure post or two that I could attach items to. The Model 3 has two adjacent bolt wells in the frunk that can double as securing points.NOTE:Earlier Tesla...
prusaprinters
To avoid smaller items rolling around in my Tesla Model 3 (2021) frunk, I was interested in a secure post or two that I could attach items to. The Model 3 has two adjacent bolt wells in the frunk that can double as securing points.NOTE:Earlier Tesla...
thingiverse
I prefer using screws over printed pins and like to avoid supports whenever possible, so I remixed these frunk hooks to use M3 screws. It's a little klugey - not sure if the original STLs were screwy or if it's because I imported the STLs into...
prusaprinters
Just remove the two existing bolts at the top of the frunk tube and insert the hooks. The hooks are not necessarily directional (ignore the “L” indicating left on the bottom). ...Recommend using a material that doesn't melt in the heat of the day. This...
thingiverse
# Tesla Model 3 Frunk Grocery Hooks ## Requires a Model 3 delivered after July/August 2020 with the new frunk design (textured bottom, not smooth) I loved that the frunk used to have grocery hooks, and when they took them out and then updated the...
prusaprinters
Add grocery hooks to your Model 3 frunk!Requires a Tesla Model 3 built on or after August 2020. Supported frunks will have two holes on the inside of the frunk weather stripping, each containing a single bolt.See pictures for correct installation and...
thingiverse
If the secondary latch on your Tesla Model 3 fails to disengage, this tool will assist you in opening the front trunk compartment.
thingiverse
Print at 100%, no support Required: 2x M3x25 hex bolt (20mm is fine too) You can support my work by purchasing the complete model from: https://cults3d.com/en/3d-model/gadget/frunk-hooks-for-tesla-model-3-my2021
thingiverse
This is a tool to help position your Tesla model3's front hood emblem perfectly, simple as that. ... tip would be appreciated :) happy printing
thingiverse
Note the position of the tow hook storage in the image if you are uncertain.[/update] This is an insert designed to level the floor of the Tesla Model 3 frunk for using it as a container without leakage or toppings sliding to one side. I was...
thingiverse
Replacement clips for a Tesla Model S that hold the frunk liner in place to the quarter panel. These are held on from the factory by adhesive strips that wear over time. Mine were practically falling off and got lost. I printed 3 as replacements and...
cults3d
A lid / cover for a 2013 Tesla Model S frunk fuse box. It is redesigned from the OEM version to let you to tap into the fuses to power other mods. I made this as part of my radar retrofit (https://www.thingiverse.com/thing:3667845) The lid is...
thingiverse
A custom lid/cover designed specifically for the 2013 Tesla Model S frunk fuse box. This redesigned version allows users to easily tap into the fuses, making it possible to power various mods. The creation of this lid was part of a larger project,...
thingiverse
The Tesla Model 3 trunk area has two parts that are poorly designed and prone to breaking when removed and replaced. A custom part was created to hold the defective piece in place, preventing it from being damaged further. ...To install this solution,...
thingiverse
This is a tool to help position your Tesla modelY's front hood emblem perfectly, simple as that. ... tip would be appreciated :) happy printing